Module Outline
Date retreived
22/07/2026 8:59 PM AWST
22/07/2026 8:59 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Conduct Electrical installation, testing and verification
Conduct Electrical installation, testing and verification
Module
National Code
ECGELE006A
ECGELE006A
State Code
AW875
AW875
DTWD Status
Approved
Approved
State Implementation and Classification
Approved Date
08/02/2016
Field of Education
031399 - Electrical And Electronic Engineering And Technology, N.e.c.
Nominal Hours
16
Description
This unit is for holders of OTSR issued by an RTO and incorporated the minimum context gap to meet Australian standards and regulations.
No information
Evidence Guide
1. Prepare to troubleshoot and rectify faults
1.1 The extent and nature of the electrical installation is determined from job specifications.
1.2 Safety and other regulatory requirements to which the electrical installation shall comply area are identified, obtained and understood.
1.3 WHS/OH&S procedures for a given work area are identified, obtained and understood.
1.4 WHS/OH&S risk control measures and procedures in preparation for the work are followed.
1.5 Safety hazards that have not previously been identified are noted and established risk control measures are implemented.
1.6 The likely extent of work to be undertaken is envisaged from fault/breakdown reports and/or discussions with appropriate person(s).
1.7 Advice is sought from the work supervisor to ensure the work is coordinated effectively with others.
2. Terminate cables, cords and conductors
2.1 WHS/OH&S risk control measures and procedures for carrying out the work are followed.
2.2 The need to test or measure live is determined in strict accordance with WHS/OH&S requirements and when necessary conducted within established safety procedures.
2.3 Circuits/machines/plant are checked as being isolated where necessary in strict accordance OHS requirements and procedures.
2.4 Safety hazards resulting from the fault or breakdown are documented and risk control measures devised and implemented in consultation with appropriate personnel.
2.5 Trouble-shooting is approached methodically drawing on knowledge of electrical circuits and apparatus using measured and calculated values of circuit/apparatus parameters.
2.6 Circuit/apparatus components are dismantled where necessary and parts stored to protect them against loss or damage.
2.7 Faulty circuits/components are rechecked and their fault status and acquired.
2.8 Unexpected situations are dealt with safely and with the approval of an authorised person.
2.9 Effectiveness of the repair is tested in accordance with established procedures.
2.10 Apparatus is reassembled, finally tested and prepared for return to service.
2.11 Unexpected situations are dealt with safely and with the approval of an authorised person.
2.12 Trouble-shooting and repair activities are carried out without damage to apparatus, circuits, the surrounding environment or services and using sustainable energy practices.
3. Test terminated cables and cords
3.1 WHS/OH&S work completion risk control measures and procedures are followed.
3.2 Work area is cleaned and made safe in accordance with established procedures.
3.3 Written justification is made for repairs to apparatus.
3.4 Work completion is documented and an appropriate person or persons notified in accordance with established procedures.
1.1 The extent and nature of the electrical installation is determined from job specifications.
1.2 Safety and other regulatory requirements to which the electrical installation shall comply area are identified, obtained and understood.
1.3 WHS/OH&S procedures for a given work area are identified, obtained and understood.
1.4 WHS/OH&S risk control measures and procedures in preparation for the work are followed.
1.5 Safety hazards that have not previously been identified are noted and established risk control measures are implemented.
1.6 The likely extent of work to be undertaken is envisaged from fault/breakdown reports and/or discussions with appropriate person(s).
1.7 Advice is sought from the work supervisor to ensure the work is coordinated effectively with others.
2. Terminate cables, cords and conductors
2.1 WHS/OH&S risk control measures and procedures for carrying out the work are followed.
2.2 The need to test or measure live is determined in strict accordance with WHS/OH&S requirements and when necessary conducted within established safety procedures.
2.3 Circuits/machines/plant are checked as being isolated where necessary in strict accordance OHS requirements and procedures.
2.4 Safety hazards resulting from the fault or breakdown are documented and risk control measures devised and implemented in consultation with appropriate personnel.
2.5 Trouble-shooting is approached methodically drawing on knowledge of electrical circuits and apparatus using measured and calculated values of circuit/apparatus parameters.
2.6 Circuit/apparatus components are dismantled where necessary and parts stored to protect them against loss or damage.
2.7 Faulty circuits/components are rechecked and their fault status and acquired.
2.8 Unexpected situations are dealt with safely and with the approval of an authorised person.
2.9 Effectiveness of the repair is tested in accordance with established procedures.
2.10 Apparatus is reassembled, finally tested and prepared for return to service.
2.11 Unexpected situations are dealt with safely and with the approval of an authorised person.
2.12 Trouble-shooting and repair activities are carried out without damage to apparatus, circuits, the surrounding environment or services and using sustainable energy practices.
3. Test terminated cables and cords
3.1 WHS/OH&S work completion risk control measures and procedures are followed.
3.2 Work area is cleaned and made safe in accordance with established procedures.
3.3 Written justification is made for repairs to apparatus.
3.4 Work completion is documented and an appropriate person or persons notified in accordance with established procedures.
Elements and Performance Criteria
No information
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| 75985 | EEOZAMCG08A | Electrical Installation, Testing and Verification - AMCG | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| AY782 | NAT10809006 | Verify compliance, functionality and aspects critical to the safety of electrical installations | Module |
Associated Qual/Courses
| State Code | National Code | Title | Type |
|---|---|---|---|
| YU04 | 10145NAT | Course in Electrician - Minimum Australian Context Gap | Accredited course |