Module Outline
Date retreived
22/07/2026 12:00 PM AWST
22/07/2026 12:00 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Install, set up and test an embedded control system
Install, set up and test an embedded control system
Module
National Code
VU23119
VU23119
State Code
AZ279
AZ279
DTWD Status
Approved
Approved
State Implementation and Classification
Approved Date
10/06/2022
Field of Education
031305 - Computer Engineering
Nominal Hours
30
Description
This unit describes the performance outcomes, skills and knowledge required to install, set up and test an embedded control system used for automatic or semi-automatic operations of a wide range of consumer and industrial equipment.
It requires the ability to plan for the installation of an embedded control system, installing the system in accordance with job instructions and carry out diagnostic testing and verification of the control systems’ functionality.
The unit applies to a person preparing to work in or working in an environment where embedded control systems are utilised to operate a range of consumer and industrial equipment.
The unit also applies to a person preparing to work in a technology environment and is suitable for use in a secondary school program with an appropriate level of supervision and support.
No occupational licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
It requires the ability to plan for the installation of an embedded control system, installing the system in accordance with job instructions and carry out diagnostic testing and verification of the control systems’ functionality.
The unit applies to a person preparing to work in or working in an environment where embedded control systems are utilised to operate a range of consumer and industrial equipment.
The unit also applies to a person preparing to work in a technology environment and is suitable for use in a secondary school program with an appropriate level of supervision and support.
No occupational licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
No information
No information
Elements and Performance Criteria
Plan to install, set up and test an embedded control system
- 1.1 Established work, health and safety (WHS) requirements and risk control measures and procedures are followed in preparation for the work task
- 1.2 Embedded control system installation and set-up requirements are determined from job sheet or instructions from client and/or supervisor
- 1.3 Other personnel in the work area are consulted and informed of the installation to ensure the work is coordinated effectively without disruption
- 1.4 Resources and equipment needed for the task are obtained in accordance with enterprise procedures and checked for correct operation and safety
- 1.5 Equipment, machines or plant are checked as being isolated, where necessary, in accordance with WHS requirements
Install and program an embedded control system
- 2.1 Embedded control system is installed, set up and configured according to job requirements, manufacturers’ manuals and enterprise procedures
- 2.2 Embedded control system is programmed either in circuit or in a programmer according to requirements, and manufacturers’ specifications
- 2.3 Decisions and methods for dealing with unexpected situations are made from discussions with client and/or supervisor, job specifications and enterprise procedures
Verify operation and complete documentation
- 3.1 Embedded control system is tested for correct operation in accordance with requirements, manufacturers’ specifications and enterprise procedures
- 3.2 Client and/or supervisor is informed of the completion of work and provided with a demonstration of the operation of the embedded control system
- 3.3 Embedded control system installation and configuration is documented and stored, in accordance with enterprise procedures
Clean up work area and store tools
- 4.1 Work site is made safe in accordance with established safety procedures
- 4.2 Equipment and tools used in installation and set-up are maintained and stored in accordance with enterprise procedures
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| AY878 | VU22829 | Install, set up and test an imbedded control system | Unit of competency |
Associated Qual/Courses
| State Code | National Code | Title | Type |
|---|---|---|---|
| BHE71 | 22697VIC | Certificate IV in Integrated Technologies | Accredited course |
| BGR99 | 22586VIC | Certificate II in Integrated Technologies (Pre-vocational) | Accredited course |