Unit of competency Outline
Date retreived
22/07/2026 5:06 PM AWST
22/07/2026 5:06 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Perform advanced plastic processing
Perform advanced plastic processing
Unit of competency
National Code
MEM07026B
MEM07026B
State Code
W5371
W5371
TGA Status
Replaced
Replaced
DTWD Status
Transition (Replaced)
Transition (Replaced)
State Implementation and Classification
Approved Date
18/06/2009
Field of Education
030305 - Materials Engineering
Original Release Date
18/06/2009
Nominal Hours
54
Description
This unit covers producing products using advanced plastic processing equipment.
Notes
Elements and Performance Criteria
1. Determine job requirements
- 1.1. Drawings, job instructions and specifications are interpreted and task requirements are understood including machine/process selection and settings.
2. Observe safety precautions
- 2.1. Safety equipment and guards are checked for correct position and operation.
3. Conduct pre-start checks
- 3.1. Programmed operational maintenance is undertaken to standard operating procedures.
- 3.2. Pre-start checks are undertaken to standard operating procedures.
- 3.3. The match of task requirements against equipment, raw material and tooling is verified.
4. Operate machine/process
- 4.1. Machine/process is started up safely and correctly.
- 4.2. Machine/process is operated in accordance with job instructions or standard operating procedures.
- 4.3. Components/feed stock are loaded and maintained consistent with production requirements.
- 4.4. Machine/process output is unloaded safely to standard operating procedures.
- 4.5. Machine/process output is handled and stored in a manner not likely to cause damage, as required.
- 4.6. Production data is recorded to standard operating procedures.
5. Monitor machine/process
- 5.1. Machine/process is monitored for safe and correct operation.
- 5.2. Emergency procedures are understood and followed in accordance with standard operating procedures.
6. Recognise and rectify deviations and faults in product/output
- 6.1. Product faults/deviations such as short shots, warped mouldings and dimensional errors are recognised from standard operating procedures, job sheets or other documentation.
- 6.2. Product faults/deviations are rectified in accordance with standard operating procedures, job sheets or other documentation and may be achieved by adjustment of machine/process settings within parameters.
7. Recognise and rectify deviations and faults with raw material/feed stock
- 7.1. Raw material faults/deviations such as contamination, colour variation are recognised from standard operating procedures, job sheets or other documentation.
- 7.2. Raw material faults/deviations are rectified in accordance with standard operating procedures, job sheets or other documentation.
8. Recognise and rectify deviations and faults in tooling
- 8.1. Tooling faults/deviations resulting in blemishes, missing detail etc. are identified against specification and reported to standard operating procedure.
- 8.2. Tooling faults/deviations are rectified in accordance with standard operating procedures, job sheets or other documentation.
9. Recognise and rectify deviations and faults in machine/process
- 9.1. Machine/process faults/deviations such as short shots, burn marks, distortion etc. are recognised from standard operating procedures, job sheets or other documentation.
- 9.2. Machine/process faults/deviations are rectified in accordance with standard operating procedures, job sheets or other documentation.
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
EVIDENCE GUIDE
The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
A person who demonstrates competency in this unit must be able to perform advanced plastic processing. Competency in this unit cannot be claimed until all prerequisites have been satisfied.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria, including required knowledge, and be capable of applying the competency in new and different situations and contexts.
Context of and specific resources for assessment
This unit may be assessed on the job, off the job or a combination of both on and off the job. Where assessment occurs off the job, that is the candidate is not in productive work, then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations. The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team. The assessment environment should not disadvantage the candidate.
This unit could be assessed in conjunction with any other units addressing the safety, quality, communication, materials handling, recording and reporting associated with advanced plastic processing or other units requiring the exercise of the skills and knowledge covered by this unit.
Method of assessment
Assessors should gather a range of evidence that is valid, sufficient, current and authentic. Evidence can be gathered through a variety of ways including direct observation, supervisor's reports, project work, samples and questioning. Questioning should not require language, literacy and numeracy skills beyond those required in this unit. The candidate must have access to all tools, equipment, materials and documentation required. The candidate must be permitted to refer to any relevant workplace procedures, product and manufacturing specifications, codes, standards, manuals and reference materials.
Guidance information for assessment
The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
A person who demonstrates competency in this unit must be able to perform advanced plastic processing. Competency in this unit cannot be claimed until all prerequisites have been satisfied.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria, including required knowledge, and be capable of applying the competency in new and different situations and contexts.
Context of and specific resources for assessment
This unit may be assessed on the job, off the job or a combination of both on and off the job. Where assessment occurs off the job, that is the candidate is not in productive work, then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations. The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team. The assessment environment should not disadvantage the candidate.
This unit could be assessed in conjunction with any other units addressing the safety, quality, communication, materials handling, recording and reporting associated with advanced plastic processing or other units requiring the exercise of the skills and knowledge covered by this unit.
Method of assessment
Assessors should gather a range of evidence that is valid, sufficient, current and authentic. Evidence can be gathered through a variety of ways including direct observation, supervisor's reports, project work, samples and questioning. Questioning should not require language, literacy and numeracy skills beyond those required in this unit. The candidate must have access to all tools, equipment, materials and documentation required. The candidate must be permitted to refer to any relevant workplace procedures, product and manufacturing specifications, codes, standards, manuals and reference materials.
Guidance information for assessment
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| OAW29 | MEM07026 | Perform advanced plastic processing | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W245 | MEM40105 | Certificate IV in Engineering | Qualification |
| W233 | MEM20105 | Certificate II in Engineering | Qualification |
| W247 | MEM50105 | Diploma of Engineering - Advanced Trade | Qualification |
| W237 | MEM30205 | Certificate III in Engineering - Mechanical Trade | Qualification |
| W236 | MEM30105 | Certificate III in Engineering - Production Systems | Qualification |
| W234 | MEM20205 | Certificate II in Engineering - Production Technology | Qualification |
| W726 | LMT31909 | Certificate III in Engineering - TCF Mechanic | Qualification |