Unit of competency Outline

Date retreived
22/07/2026 3:49 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Modify/repair aircraft component single layer printed circuit boards

Modify/repair aircraft component single layer printed circuit boards

Unit of competency
National Code
MEA262B
State Code
W8392
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
2.00
Current Release Date
23/01/2012
View on TGA
State Implementation and Classification
Approved Date
06/05/2011
Field of Education
031317 - Electronic Equipment Servicing
Original Release Date
06/05/2011
Nominal Hours
16
Description
This unit of competency is part of the Avionic Certificate IV training pathways. It covers the competencies required to modify or repair single layer printed circuit boards. The unit is used in workplaces that operate under the airworthiness regulatory systems of the ADF and CASA.
Notes
Elements and Performance Criteria
1. Inspect single layer printed circuit cards and associated components
  • 1.1. Relevant maintenance documentation, including component defect reports where applicable, is interpreted and matched by part and serial number
  • 1.2. Preparation of work area and circuit card assemblies is appropriate to allow for effective detailed inspection of all substrate, circuit tracks, edge connectors and attached components, taking into account any static discharge procedures
  • 1.3. Circuit card assemblies are visually or physically inspected for physical integrity of substrate, circuit tracks, edge connectors and attached components
  • 1.4. Modification status is established to assist in determining repair requirements
  • 1.5. Defects are correctly identified and reported
2. Test single layer printed circuit cards and associated components
  • 2.1. Circuit card assemblies are correctly prepared and connected to the appropriate test facility in accordance with approved procedures, or circuit card assemblies are correctly prepared and connected in situ to allow required test procedures to be performed
  • 2.2. Circuit card assemblies are functionally tested in accordance with normal trade practice and approved maintenance documentation for evidence of serviceability or malfunction
  • 2.3. Circuit card assemblies, attached hardware and electronic components are electronically and/or physically adjusted/aligned in accordance with maintenance manuals or other prescribed procedures
3. Troubleshoot single layer printed circuit cards and associated components
  • 3.1. Maintenance documentation, physical inspection and test results are used, where applicable, to assist in fault determination
  • 3.2. Maintenance manual fault diagnosis guides, logical processes and test equipment are used appropriately to ensure efficient and accurate troubleshooting
  • 3.3. Component faults are located and the causes of the faults are clearly identified and recorded in maintenance documentation, where required
  • 3.4. Rectification requirements are determined
4. Dismantle single layer printed circuit cards and associated components
  • 4.1. Conformal/protective coatings are removed from the circuit card assembly to the extent required to effect necessary repairs and in accordance with maintenance manuals, industry or enterprise standards as applicable
  • 4.2. Appropriate OHS precautions are observed at all times during maintenance procedure
  • 4.3. Circuit card assembly is dismantled to the extent necessary to allow repair of all identified faults
  • 4.4. Parts for processing are correctly tagged and despatched
  • 4.5. Parts for retention and re-fitment are correctly packaged and stored in accordance with approved procedures to avoid physical and electrostatic damage
  • 4.6. Parts for disposal are correctly packaged and processed to accord with statutory requirements pertaining to dangerous goods
5. Assemble single layer printed circuit cards and associated components
  • 5.1. Parts removed for access, and replacement parts, are collected ensuring appropriate modification status, component tolerances and assembly configuration is maintained
  • 5.2. Printed circuit card and associated components are assembled in accordance with maintenance manuals, and all electrical joints meet the approved standard of the equipment manufacturer, or industry standard, as appropriate
  • 5.3.Circuit substrate material, circuit tracks, edge connectors and through-hole eyelets are reworked, as necessary, to restore printed circuit card to a serviceable condition
  • 5.4. Any conformal/protective coatings removed are replaced to the approved standard of the equipment manufacturer, or industry standard, as appropriate
  • 5.5.Rework techniques are in accordance with industry approval procedures and relevant OHS requirements are observed
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Circuit card components
Attached components include:
capacitors, resistors, wires, semiconductors, inductors, transformers, switches, connectors, multi-pin ICs, terminal posts and heat-sink materials and will include electrostatic sensitive devices
Application
Application of this unit may relate to:
scheduled or unscheduled maintenance activities
individual or team-related activities
single layer printed circuit card assemblies with substrates made from fibreglass, phenolic, composite fibre and epoxy resins and coatings that are from a wide range of aircraft systems
Procedures and standards
Procedures and standards for repair of printed circuit card assemblies include:
a range of general engineering hand skills in addition to specific high reliability soldering skills
standards applicable in a given situation will be defined by equipment manufacturers and/or regulatory authorities and the enterprise
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
A person who demonstrates competency in this unit must be able to repair single layer circuit boards in accordance with procedures and standards while applying all relevant safety precautions.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
It is essential that substrate abrasion and rebuilding techniques, and precautions associated with handling and assembly of electrostatic and temperature sensitive devices are fully observed, understood and complied with. A high level of awareness of safety precautions associated with beryllium materials and use of fluxes and solvents is to be demonstrated.
Evidence of transferability of skills and knowledge related to single layer printed circuit card assembly and repair is essential before undertaking any action. This may be demonstrated through application of the techniques involved across a representative range of circuit card substrate materials and attached components. The work plan should take account of applicable safety and quality requirements in accordance with the industry and regulatory standards. Use of high precision, high reliability soldering techniques and handling of components, including application of anti-static equipment, must be demonstrated.
A person cannot be assessed as competent until it can be demonstrated to the satisfaction of the workplace assessor that the relevant elements of the unit of competency are being achieved under routine supervision on a representative range of cards with various substrate materials and components. This shall be established via the records in the Log of Industrial Experience and Achievement or, where appropriate, an equivalent Industry Evidence Guide.
Context of and specific resources for assessment
Competency should be assessed in the work environment or simulated work environment, using tools and equipment specified in maintenance manuals. It is also expected that general and special purpose test equipment found in most routine situations would be used where appropriate.
Method of assessment

Guidance information for assessment
Replaces
State Code National Code Title Type
W1116 MEA262A Modify/repair single layer printed circuit boards Unit of competency
Replaced By
State Code National Code Title Type
AUE15 MEA262 Modify/repair aircraft component single layer printed circuit boards Unit of competency