Unit of competency Outline

Date retreived
22/07/2026 3:13 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Fabricate and install commercial glazing

Fabricate and install commercial glazing

Unit of competency
National Code
MSFGG3017
State Code
WI499
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
2.00
Current Release Date
10/09/2015
View on TGA
State Implementation and Classification
Approved Date
19/06/2014
Field of Education
040323 - Glazing
Original Release Date
19/06/2014
Nominal Hours
52
Description
This unit of competency covers planning, fabricating and installing flat or curved glass in commercial shopfronts, doors and windows. Licensing, legislative or certification requirements may apply to this unit and relevant state/territory and local government agencies should be consulted to determine any necessary certification or licensing for undertaking glass and glazing work. Access to construction sites requires certification of general induction training specified by the National Code of Practice for Induction for Construction Work (ASCC 2007).
Notes
Elements and Performance Criteria
1 Identify work requirements
  • 1.1 Work requirements in the form of type of glass, frames and the method of fixing are identified from work instructions
  • 1.2 Work health and safety (WHS) requirements for fabrication and installation of commercial glazing, including personal protective equipment, are identified and observed throughout the work
  • 1.3 Process for fabricating and installing commercial flat and/or curved glazing is determined
2 Prepare for work
  • 2.1 Work sequence is planned in a logical order to suit the job and workplace procedures
  • 2.2 Tools, equipment and materials, other than glass and frames, are selected and checked prior to use to ensure they are appropriate for the work, serviceable and in a safe condition
  • 2.3 Type of glass to be fitted and frames are selected to match the customer order
  • 2.4 Glass is checked for type, size and imperfections
  • 2.5 Glass fixing method and appropriate method of glazing are selected
3 Identify site conditions and constraints
  • 3.1 Site safety hazards are recognised and corrective action taken to reduce injury to self and others
  • 3.2 Other on-site difficulties are identified and corrective action taken in accordance with regulations and enterprise agreements
  • 3.3 Special characteristics of the glass aperture are identified in relation to the effect of the glass fitting process on the finished job
  • 3.4 Covering material is applied, where necessary, to protect existing fixtures and fittings
4 Prepare frame
  • 4.1 Frame condition is assessed to ensure suitability for glazing in accordance with customer order and Australian Standards
  • 4.2 Defective frames are reported for repair or replacement in accordance with workplace procedures
  • 4.3 Frame is prepared, if required, to receive glass
  • 4.4 Fixing and sealing materials are prepared by mixing or cutting to length, as appropriate
5 Fit glass
  • 5.1 Glass is fixed to the frame using the selected method and in accordance with recognised Australian and industry standards
  • 5.2 Solvents and sealants are used in accordance with manufacturer recommendations and Australian Standards
  • 5.3 Excess sealing material is removed and the glass and frame are cleaned after fixing
6 Complete work
  • 6.1 Completed installation is checked to ensure compliance with customer requirements, specifications and Australian Standards
  • 6.2 Work area is cleaned and left in a safe condition and rubbish removed from work area and disposed of in accordance with relevant statutory requirements and workplace requirements
  • 6.3 Tools, equipment and materials are cleaned and stored following workplace procedures
  • 6.4 Waste and scrap material are removed for disposal or recycling, as required
  • 6.5 Workplace documentation is completed in accordance with workplace requirements including calculating the cost of glass, fittings, materials and labour
No information
No information
Replaces
State Code National Code Title Type
S7833 LMFGG3017C Fabricate and install commercial glazing Unit of competency
Replaced By
State Code National Code Title Type
OAJ08 MSFGG3036 Install commercial glazing products Unit of competency
State Code National Code Title Type
J732 MSF30413 Certificate III in Glass and Glazing Qualification
BDJ4 CPC30116 Certificate III in Shopfitting Qualification