Unit of competency Outline

Date retreived
22/07/2026 2:57 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Service and repair chainsaw cutting systems

Service and repair chainsaw cutting systems

Unit of competency
National Code
AURP245371B
State Code
D7634
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
21/06/2011
View on TGA
State Implementation and Classification
Approved Date
12/10/2011
Field of Education
030503 - Vehicle Mechanics
Original Release Date
12/10/2011
Nominal Hours
16
Description
This unit of competency describes the skills and knowledge required to service and repair chainsaw cutting systems, including removal, repair/replacement, fitting and adjustment of components.No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.This unit replaces AURP245371A Service and repair faults in chainsaw cutting systems.
Notes
Elements and Performance Criteria
1. Prepare for service and repair operation
  • 1.1. Identify and confirm work to be carried out
  • 1.2. Access and interpret service and repair procedures, workshop manuals and manufacturer information
  • 1.3. Identify and prepare tools, equipment and materials required for servicing and repair job
  • 1.4. Set up work area
2. Determine service and repair requirements
  • 2.1. Check customer requirements and equipment specifications following workplace procedures
  • 2.2. Follow safety procedures, including personal protection needs, for handling chainsaws
  • 2.3. Remove chain and guide bar and inspect for wear and damage
  • 2.4. Plan and cost service and repair procedure
  • 2.5. Discuss recommended repair process with customer and obtain authorisation to proceed
3. Service and repair chainsaw cutting system
  • 3.1. Select tooling and equipment to meet job requirements and check to ensure they are in good working order
  • 3.2. Check equipment manufacturer/component supplier service specifications and recommendations
  • 3.3. Remove components for repair procedure and inspect for condition and serviceability
  • 3.4. Discard unusable components and retain reusable and repairable components following workplace procedures
  • 3.5. Determine availability of replacement parts, qualified repair staff or subcontractors
  • 3.6. Fit reusable, repaired and replacement parts in accordance with manufacturer/component supplier specifications and workplace procedures
  • 3.7. Sharpen chain cutting system components to provide effective cutting edges
  • 3.8. Adjust and tension components in accordance with manufacturer/component supplier specifications
  • 3.9. Perform lubrication and alignment checks
4. Check chainsaw cutting system for normal operation
  • 4.1. Identify and observe applicable occupational health and safety (OHS) requirements, including state/territory regulatory requirements and personal protection needs, for operating a chainsaw
  • 4.2. Start up chainsaw and check operation of safety features against equipment specifications
  • 4.3. Make any adjustments as required and re-test
  • 4.4. Check adjustments, fluid levels and alignments
  • 4.5. Complete workplace documentation and update customer and warranty information as required
5. Complete work and return unit to customer
  • 5.1. Inspect repaired unit to ensure protective guards, cowlings and safety features are in place
  • 5.2. Clean unit to workplace expectations
  • 5.3. Clean work area, dispose of waste, and store tools and equipment in accordance with workplace procedures
  • 5.4. Provide customer report on repairs and replacements and explain follow-up adjustments, use and care of equipment and warranty requirements
No information
No information
Replaces
State Code National Code Title Type
W2918 AURP245371A Service and repair chainsaw cutting systems Unit of competency
Replaced By
State Code National Code Title Type
WF297 AURPTA2005 Service and repair chainsaw cutting systems Unit of competency
State Code National Code Title Type
D542 AUR30711 Certificate III in Outdoor Power Equipment Qualification