Unit of competency Outline
Date retreived
22/07/2026 9:44 AM AWST
22/07/2026 9:44 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Operate tyre curing equipment
Operate tyre curing equipment
Unit of competency
National Code
PMBPROD262B
PMBPROD262B
State Code
W7589
W7589
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
08/12/2008
Field of Education
030717 - Plant And Machine Operations
Original Release Date
08/12/2008
Nominal Hours
20
Description
This competency covers the operation of tyre curing equipment in a tyre manufacturing plant or retreading situation where the 'green' tread is laid on the tyre casing.
Notes
Elements and Performance Criteria
1. Check work requirements.
- 1.1 Identify work requirements from production plan or request.
- 1.2 Check product, materials and equipment meet requirements for job(s).
- 1.3 Recognise requirements which may not be in accordance with usual practice.
- 1.4 Ask questions of appropriate person to confirm unusual practice.
- 1.5 Identify hazards associated with the job and take appropriate action.
- 1.6 Perform other pre-operational checks in accordance with procedures.
2. Start up tyre curing equipment to procedures.
- 2.1 Conduct pre-start checks.
- 2.2 Start up tyre curing equipment.
3. Operate equipment to procedures.
- 3.1 Start machine safely and correctly when required.
- 3.2 Check process is operating within required limits.
- 3.3 Check product is in specification and to required quality standard.
- 3.4 Ensure product is consistently ready for next operation.
- 3.5 Maintain supply of material(s) as required.
- 3.6 Complete logs and records when as required.
- 3.7 Collect and segregate scrap, trim and other materials as required in accordance with procedures.
- 3.8 Keep equipment and work area clean area in accordance with procedures.
- 3.9 Pause machine cycle and perform emergency stop, as required by procedures.
4. Respond to routine problems in accordance with procedures.
- 4.1 Recognise known faults that occur during the operation.
- 4.2 Identify and take action on causes of routine faults.
- 4.3 Log problems as required.
- 4.4 Identify non-routine process and quality problems and take appropriate action.
RANGE STATEMENT
The Range Statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Add any essential operating conditions that may be present with training and assessment depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts.
Where reference is made to industry codes of practice, and/or Australian/international standards, the latest version must be used.
Context
This competency unit includes curing operations.
This competency applies to all work environments within the tyre manufacture sector. It also includes the operation of all relevant ancillary equipment.
Procedures
All operations are performed in accordance with procedures.
Procedures include all relevant workplace procedures, work instructions, temporary instructions and relevant industry and government codes and standards.
Tools and equipment
This competency includes use of equipment and tools such as:
curing press (eg bagomatic, collapsible bladder or shear strip, solid bladder
ancillary equipment (eg screens/strainers, computer data systems, ball float steam traps, condensate temperature and steam trap monitoring system)
curing agents (eg sulphur sources, peroxides, metal oxides, amines, and phenolic resins)
relevant personal protective equipment.
Hazards
Typical hazards include:
manual handling
noise
humidity
temperatures (eg from air and steam)
fumes/vapours (eg from curing agents)
cleaning equipment (eg screens/strainers)
stationary and moving machinery.
Problems
'Respond to routine problems' means 'apply known solutions to a limited range of predictable problems'. Typical process problems may include:
poorly aligned guides
mould incorrectly placed on machine
poor mould closure/alignment
poorly prepared mould (dirty/mould release)
incorrect temperature settings
mould temperature/steam pressure/air blinded/waterlogged
mould/air pressure.
Typical product problems may include:
contaminated green tyres
squashed or distorted green tyres
scorched rubber
curing time/cycle
product
excessive trim/spue
out of round/eccentric.
The Range Statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Add any essential operating conditions that may be present with training and assessment depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts.
Where reference is made to industry codes of practice, and/or Australian/international standards, the latest version must be used.
Context
This competency unit includes curing operations.
This competency applies to all work environments within the tyre manufacture sector. It also includes the operation of all relevant ancillary equipment.
Procedures
All operations are performed in accordance with procedures.
Procedures include all relevant workplace procedures, work instructions, temporary instructions and relevant industry and government codes and standards.
Tools and equipment
This competency includes use of equipment and tools such as:
curing press (eg bagomatic, collapsible bladder or shear strip, solid bladder
ancillary equipment (eg screens/strainers, computer data systems, ball float steam traps, condensate temperature and steam trap monitoring system)
curing agents (eg sulphur sources, peroxides, metal oxides, amines, and phenolic resins)
relevant personal protective equipment.
Hazards
Typical hazards include:
manual handling
noise
humidity
temperatures (eg from air and steam)
fumes/vapours (eg from curing agents)
cleaning equipment (eg screens/strainers)
stationary and moving machinery.
Problems
'Respond to routine problems' means 'apply known solutions to a limited range of predictable problems'. Typical process problems may include:
poorly aligned guides
mould incorrectly placed on machine
poor mould closure/alignment
poorly prepared mould (dirty/mould release)
incorrect temperature settings
mould temperature/steam pressure/air blinded/waterlogged
mould/air pressure.
Typical product problems may include:
contaminated green tyres
squashed or distorted green tyres
scorched rubber
curing time/cycle
product
excessive trim/spue
out of round/eccentric.
The Evidence Guide provides advice on assessment and must be read in conjunction with the Performance Criteria, required skills and knowledge, the Range Statement and the Assessment Guidelines for this Training Package.
Overview of assessment
A holistic approach should be taken to the assessment.
Assessors must be satisfied that the person can consistently perform the unit as a whole, as defined by the Elements, Performance Criteria and skills and knowledge.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
It is essential that competence is demonstrated in the knowledge and skills defined in this unit. These may include the ability to:
apply the required skills and knowledge to operate a tyre curing machine
apply approved procedures.
Consistent performance should be demonstrated. For example, look to see that:
tyre curing production standards are met consistently
all safety procedures are followed.
Assessment method and context
Assessment will occur on an industrial curing machine(s) equipment and will be undertaken in a work-like environment.
Competence in this unit may be assessed:
by using an appropriate, industrial tyre curing machine requiring demonstration of operation and emergency stop procedures
in a situation allowing for the generation of evidence of the ability to respond to problems
by using a suitable simulation and/or a range of case studies/scenarios
through a combination of these techniques.
In all cases it is expected that practical assessment will be combined with targeted questioning to assess the underpinning knowledge and theoretical assessment will be combined with appropriate practical/simulation or similar assessment. Assessors need to be aware of any cultural issues that may affect responses to questions.
Assessment processes and techniques must be culturally appropriate and appropriate to the oracy, language and literacy capacity of the assessee and the work being performed.
Specific resources for assessment
This section should be read in conjunction with the Range Statement for this unit of competency. Resources required include suitable access to an operating plant or equipment that allows for appropriate and realistic simulation. A bank of case studies/scenarios and questions will also be required to the extent that they form part of the assessment method. Questioning may take place either in the workplace, or in an adjacent, quiet facility such as an office or lunchroom. No other special resources are required.
Access must be provided to appropriate learning and/or assessment support when required. Where applicable, physical resources should include equipment modified for people with disabilities.
Overview of assessment
A holistic approach should be taken to the assessment.
Assessors must be satisfied that the person can consistently perform the unit as a whole, as defined by the Elements, Performance Criteria and skills and knowledge.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
It is essential that competence is demonstrated in the knowledge and skills defined in this unit. These may include the ability to:
apply the required skills and knowledge to operate a tyre curing machine
apply approved procedures.
Consistent performance should be demonstrated. For example, look to see that:
tyre curing production standards are met consistently
all safety procedures are followed.
Assessment method and context
Assessment will occur on an industrial curing machine(s) equipment and will be undertaken in a work-like environment.
Competence in this unit may be assessed:
by using an appropriate, industrial tyre curing machine requiring demonstration of operation and emergency stop procedures
in a situation allowing for the generation of evidence of the ability to respond to problems
by using a suitable simulation and/or a range of case studies/scenarios
through a combination of these techniques.
In all cases it is expected that practical assessment will be combined with targeted questioning to assess the underpinning knowledge and theoretical assessment will be combined with appropriate practical/simulation or similar assessment. Assessors need to be aware of any cultural issues that may affect responses to questions.
Assessment processes and techniques must be culturally appropriate and appropriate to the oracy, language and literacy capacity of the assessee and the work being performed.
Specific resources for assessment
This section should be read in conjunction with the Range Statement for this unit of competency. Resources required include suitable access to an operating plant or equipment that allows for appropriate and realistic simulation. A bank of case studies/scenarios and questions will also be required to the extent that they form part of the assessment method. Questioning may take place either in the workplace, or in an adjacent, quiet facility such as an office or lunchroom. No other special resources are required.
Access must be provided to appropriate learning and/or assessment support when required. Where applicable, physical resources should include equipment modified for people with disabilities.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| C5629 | PMBPROD262A | Operate tyre curing equipment | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| BAJ06 | PMBPROD262 | Operate tyre curing equipment | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| AC947 | MEASS00415 | MTA068 Aircraft tyre retreading (basic) | Skill set |
| W399 | PMB20107 | Certificate II in Polymer Processing | Qualification |
| W400 | PMB30107 | Certificate III in Polymer Processing | Qualification |
| W401 | PMB40107 | Certificate IV in Polymer Technology | Qualification |