Unit of competency Outline

Date retreived
22/07/2026 7:46 AM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Set up, operate and maintain basic static machines

Set up, operate and maintain basic static machines

Unit of competency
National Code
LMFFM2010B
State Code
W8607
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
11/05/2009
View on TGA
State Implementation and Classification
Approved Date
19/06/2014
Field of Education
030717 - Plant And Machine Operations
Original Release Date
19/06/2014
Nominal Hours
56
Description
This unit covers the competency to operate and maintain basic static machines used for sawing, planing, sanding and drilling in the production of furniture
Notes
Elements and Performance Criteria
1. Prepare for work
  • 1.1. Work instructions are used to determine job requirements, including design, quality, materials, equipment, and quantities
  • 1.2. Cutting list and job specifications are read and interpreted
  • 1.3. Workplace health and safety requirements, including ventilation requirements and personal protection needs, are observed throughout the work
  • 1.4. Material for machining is selected and inspected for quality
  • 1.5. Machines, cutting tools and jigs are identified and checked for safe and effective operation
  • 1.6. Procedures are determined for minimising waste material
  • 1.7. Procedures are identified for maximising energy efficiency while completing the job
2. Set up machines
  • 2.1. Safety equipment, including emergency stops, gauges, guards and controls are checked
  • 2.2. Machine settings and adjustments are made in accordance with job requirements and machine and tool manufacturers' instructions
  • 2.3. Trial runs are conducted to check machine operation, accuracy and quality of finished work
  • 2.4. Necessary adjustments are made to machine settings
3. Operate machines
  • 3.1. Machine start-up procedure is carried out in accordance with manufacturers' instructions
  • 3.2. Material is fed into machine in accordance with manufacturers' instructions, safe handling procedures and standard workplace operating procedures
  • 3.3. Machine is operated in accordance with its designed capacity and purpose, tooling requirements and to manufacturers' recommendations
  • 3.4. Machine operation is monitored to ensure product quality and output
  • 3.5. Waste quantities are checked and minimised
  • 3.6. Items that do not meet quality requirements are repaired, recycled or discarded according to workplace procedures
  • 3.7. Problems with the required work and/or the operation of the machine are identified and reported to appropriate persons
4. Clean up work area and maintain equipment
  • 4.1. Material that can be reused is collected and stored
  • 4.2. Waste and scrap are removed following workplace procedures
  • 4.3. Equipment and work area are cleaned and inspected for serviceable condition in accordance with workplace procedures
  • 4.4. Operator maintenance is completed in accordance with manufacturers' specifications and site procedures
  • 4.5. Unserviceable equipment is tagged and faults identified in accordance with workplace procedures
  • 4.6. Equipment and tooling are maintained in accordance with workplace procedures
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
The unit scope is to cover all the following basic machines and functions or tasks:
cross-cut saw
remove/replace saw blade
blade selection/identification
docking (oversize + 20mm)
docking (accurate to +/- 0.25mm)
docking square (no tolerance)
machine fault finding
rip saw
remove/replace saw blade
blade selection/identification
set up riving knife to AS 1473
parallel rip (oversize by 5mm+)
machine fault finding
scroll band saw
remove/replace saw blade
fold, unfold, reverse saw blade
blade selection
off fence ripping
freehand ripping
freehand curve cutting
machine fault finding
panel saw
remove/replace saw blade
set up scribe saw
set up riving knife to AS 1473
cut flat panel board (off rip fence using scribe saw)
cut flat panel board (off cross-cut fence using scribe saw)
machine fault finding
surface planer (buzzer/jointer)
machine face
machine edge
machine chamfer or bevel
machine fault finding
panel planer (thicknesser)
parallel plane width
parallel plane thickness
machine fault finding
bobbin sander
sand concave surface
machine fault finding
disc sander
sand straight surface
sand convex surface
sand end grain
machine fault finding
belt sander (including linisher, edge sander and stroke [lacey] sander)
remove/replace belts
sand veneer face of flat panel board
sand solid timber face
sand solid timber edges (remove arris/shape)
machine fault finding
vertical drill press
select and replace drill bits
drill holes to pre-determined depths vertically
hinge boring
machine fault finding
horizontal borer (single bit)
select and replace drill bits
drill holes to pre-determined depths horizontally
hinge boring
machine fault finding
Unit context
OH&S requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the set-up, operation and maintenance of machines
Competency may be demonstrated in workplaces involved in the manufacture of solid timber furniture, domestic furniture, commercial furniture, kitchen and bathroom cabinets and/or furniture components
Material to be machined may include but is not limited to:
solid timber
manufactured board and metal
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, cutting lists, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturers' specifications and operational procedures








EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Critical Aspects of Evidence
Read and interpret cutting lists and job specifications to prepare for work
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment and products
maintain required production output and product quality
Identify, set up, operate and monitor the machines and complete the tasks identified in the Range Statement (above)
Work effectively with others
Modify activities to cater for variations in workplace context and environment

Resource Implications
Access to basic static machinery as identified in the Range Statement, standard operating procedures, and unprocessed materials.

Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other units of competency.

Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.


Replaces
State Code National Code Title Type
W0281 LMFFM2010A Set up, operate and maintain basic static machines Unit of competency
Replaced By
State Code National Code Title Type
WI419 MSFFM2010 Set up and operate basic static machines Unit of competency