Unit of competency Outline

Date retreived
22/07/2026 9:04 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Carry out cemetery monument fixing

Carry out cemetery monument fixing

Unit of competency
National Code
CPCCST3013
State Code
OCM52
TGA Status
Current
DTWD Status
Approved
Current Release Number
2.00
Current Release Date
24/12/2024
View on TGA
State Implementation and Classification
Approved Date
01/06/2021
Field of Education
040309 - Bricklaying And Stonemasonry
Original Release Date
01/06/2021
Nominal Hours
32
Description
This unit specifies the skills and knowledge required to construct and fit cemetery monuments. It includes the use of granite, marble, basalt, pre-cast concrete sections and manufactured stone. This unit applies to stonemasons who work independently, in a team or under supervision to carry out stonemasonry work relating to cemetery monument fixing in a workshop setting, on a new or existing structure.A person working at this level would be expected to take responsibility for organising and completing tasks assigned to them without needing close supervision.Completion of the general construction induction training program specified by the model Code of Practice for Construction Work is required for any person who is to carry out construction work. Achievement of CPCWHS1001Prepare to work safely in the construction industrymeets this requirement.No licensing, legislative or certification requirements apply to this unit at the time of publication.
Notes
Elements and Performance Criteria
1 Plan the work.
  • 1.1 Read, interpret and apply monument fixing requirements from current job instructions, specifications and codes.
  • 1.2 Follow relevant information from workplace procedures, workplace safety and environmental documentation.
  • 1.3 Determine job priorities and sequence job tasks in consultation with others on site.
  • 1.4 Identify potential hazards and determine and implement control measures.
  • 1.5 Use measurements and apply formulas to calculate material quantities.
  • 1.6 Select and check condition of plant, equipment and tools and report damage or malfunction to relevant personnel.
  • 1.7 Check conformity of materials against the job requirements and report inconsistencies to relevant person.
2 Construct footings and prepare monument stones.
  • 2.1 Select, fit correctly and use personal protective equipment (PPE) appropriate for job.
  • 2.2 Set out and excavate trench to specified dimensions.
  • 2.3 Place reinforcement, fix formwork and pour concrete footings.
  • 2.4 Set out and install monument on footing.
3 Position side stones.
  • 3.1 Position side stones, plumb and pack to provide a slight fall towards front stone.
  • 3.2 Check side stones are aligned, level, parallel and square.
  • 3.3 Measure, mark, cut and insert abutting dowels.
4 Stand front and back stones.
  • 4.1 Mix mortar, insert into side stone holes and insert dowel joints to full depth.
  • 4.2 Position back stone on timber packing in preparation to lift into place and protect side stones to prevent chipping.
  • 4.3 Place mortar and lift back stone into position and pack level.
  • 4.4 Locate, raise and position front stone and pack to ensure level and plumb.
  • 4.5 Mix grout and pack joints between base and kerb stones.
  • 4.6 Remove excess grout and clean and wash kerb stones.
5 Fix headstone to back stone.
  • 5.1 Measure and cut dowels for joints, apply mortar or adhesive and insert dowels.
  • 5.2 Raise and lower headstone into position and finish plumb and level.
6 Fill centre and finish with chip top.
  • 6.1 Fill and compact centre area base to specified height.
  • 6.2 Place brick supports in each corner, cut and fix reinforcement and pour a minimum 50 mm concrete slab.
  • 6.3 Mix and spread stone screening to required finished height.
7 Fit cover stone and finish monument.
  • 7.1 Measure and cut dowels for joints, prepare and fill centre area and fill dowel holes with mortar and fully insert dowels into position.
  • 7.2 Shift cover stone into place on timber packing, and lower into place using wedges to finish in position.
  • 7.3 Prepare and apply pointing/grouting material to finish joints.
  • 7.4 Remove excess mortar, and clean and polish cover stone.
8 Clean up.
  • 8.1 Clear the work area, and dispose of, reuse or recycle materials following workplace and environmental requirements.
  • 8.2 Clean tools and equipment, check for serviceability and report damage or faults.
  • 8.3 Store and secure tools and equipment following workplace procedures.
No information
No information
Replaces
State Code National Code Title Type
W9568 CPCCST3013A Carry out cemetery monument fixing Unit of competency
State Code National Code Title Type
BGE7 CPC32320 Certificate III in Stonemasonry Qualification