Unit of competency Outline
Date retreived
22/07/2026 2:45 PM AWST
22/07/2026 2:45 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Perform engine top-end overhaul
Perform engine top-end overhaul
Unit of competency
National Code
MEM18034B
MEM18034B
State Code
W5579
W5579
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
29/05/2008
Field of Education
030503 - Vehicle Mechanics
Original Release Date
29/05/2008
Nominal Hours
72
Description
This unit covers dismantling, cleaning and assessing parts, recording and interpreting measurements, and reconditioning the cylinder head.
Notes
Elements and Performance Criteria
1. Dismantle clean and assess parts
- 1.1. Characteristics of surface finishes and wear patterns associated with valve operating mechanisms and cylinder head are understood.
- 1.2. Cylinder head and ancillary components are disassembled according to manufacturers' recommendations.
- 1.3. Parts are assessed for abnormal wear or defects.
- 1.4. Appropriate cleaning solution/procedure is selected.
- 1.5. Parts are correctly cleaned and stored ready for reassembly.
- 1.6. Parts are racked or set out according to their original location in the engine.
2. Record and interpret measurements
- 2.1. Measurements are accurately obtained and recorded using appropriate measuring equipment.
- 2.2. Parts are replaced or reused, and appropriate under/over size of replacement parts is determined.
3. Recondition cylinder head
- 3.1. Cylinder head is correctly pressure tested for serviceability.
- 3.2. Spring tensions, valve and guide dimensions and surface flatness are measured and recorded.
- 3.3. Cylinder head is removed according to manufacturers' specification.
- 3.4. Grinding and cleaning equipment is correctly used.
- 3.5. Operational parameters of cylinder head components are understood and applied in determining whether components are reconditioned or replaced.
- 3.6. Injectors sleeves, sealing washers, plugs, capping etc. are replaced correctly.
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
EVIDENCE GUIDE
The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
A person who demonstrates competency in this unit must be able to perform engine top-end overhaul. Competency in this unit cannot be claimed until all prerequisites have been satisfied.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria, including required knowledge, and be capable of applying the competency in new and different situations and contexts.
Context of and specific resources for assessment
This unit may be assessed on the job, off the job or a combination of both on and off the job. Where assessment occurs off the job, that is the candidate is not in productive work, then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations. The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team. The assessment environment should not disadvantage the candidate.
This unit could be assessed in conjunction with any other units addressing the safety, quality, communication, materials handling, recording and reporting associated with performing engine top-end overhaul, or other units requiring the exercise of the skills and knowledge covered by this unit.
Method of assessment
Assessors should gather a range of evidence that is valid, sufficient, current and authentic. Evidence can be gathered through a variety of ways including direct observation, supervisor's reports, project work, samples and questioning. Questioning techniques should not require language, literacy and numeracy skills beyond those required in this unit of competency. The candidate must have access to all tools, equipment, materials and documentation required. The candidate must be permitted to refer to any relevant workplace procedures, product and manufacturing specifications, codes, standards, manuals and reference materials.
Guidance information for assessment
The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
A person who demonstrates competency in this unit must be able to perform engine top-end overhaul. Competency in this unit cannot be claimed until all prerequisites have been satisfied.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria, including required knowledge, and be capable of applying the competency in new and different situations and contexts.
Context of and specific resources for assessment
This unit may be assessed on the job, off the job or a combination of both on and off the job. Where assessment occurs off the job, that is the candidate is not in productive work, then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations. The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team. The assessment environment should not disadvantage the candidate.
This unit could be assessed in conjunction with any other units addressing the safety, quality, communication, materials handling, recording and reporting associated with performing engine top-end overhaul, or other units requiring the exercise of the skills and knowledge covered by this unit.
Method of assessment
Assessors should gather a range of evidence that is valid, sufficient, current and authentic. Evidence can be gathered through a variety of ways including direct observation, supervisor's reports, project work, samples and questioning. Questioning techniques should not require language, literacy and numeracy skills beyond those required in this unit of competency. The candidate must have access to all tools, equipment, materials and documentation required. The candidate must be permitted to refer to any relevant workplace procedures, product and manufacturing specifications, codes, standards, manuals and reference materials.
Guidance information for assessment
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| M0443 | MEM18.34AA | Perform engine top-end overhaul | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| OAT07 | MEM27031 | Perform engine top-end overhaul | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W245 | MEM40105 | Certificate IV in Engineering | Qualification |
| W247 | MEM50105 | Diploma of Engineering - Advanced Trade | Qualification |
| W237 | MEM30205 | Certificate III in Engineering - Mechanical Trade | Qualification |
| W726 | LMT31909 | Certificate III in Engineering - TCF Mechanic | Qualification |