Unit of competency Outline
Date retreived
22/07/2026 7:43 AM AWST
22/07/2026 7:43 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Cut and handle glazing materials for framing
Cut and handle glazing materials for framing
Unit of competency
National Code
LMFPF2006B
LMFPF2006B
State Code
W8726
W8726
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
19/09/2008
Field of Education
030199 - Manufacturing Engineering And Technology, N.e.c.
Original Release Date
19/09/2008
Nominal Hours
24
Description
This unit addresses the knowledge and skills required to cut and handle glazing materials for picture and mirror frames. It includes sheet acrylic.
Notes
Elements and Performance Criteria
1. Identify work requirement
- 1.1. Work requirements, including materials, types of cuts and quantities required are identified from work instructions or job order in accordance with workplace procedures
- 1.2. Workplace health and safety requirements, including personal protection needs, are observed throughout the work
- 1.3. Tools, equipment and materials are selected and checked prior to use to ensure that they are appropriate for the work, serviceable and in a safe condition
- 1.4. Cutting list and quality standards are determined and procedures identified in accordance with workplace requirements
- 1.5. Glazing material to be cut is selected using information from the work order, including type, thickness, colour and dimensions
- 1.6. Machines, equipment and settings required to perform the work are identified
2. Prepare for work
- 2.1. Sequence of work is planned to ensure cutting is conducted in a logical order
- 2.2. Suitable cutting and lubrication methods are selected
- 2.3. Cutting table is selected and work surface is cleared of debris and dust
- 2.4. Work area is cleared of obstructions and potential hazards
- 2.5. Glazing material is checked for imperfections and damage prior to handling
- 2.6. Glazing material to be processed is located in the work area using correct manual handling procedures and any specialised handling techniques and precautions, observing any labelling instructions
- 2.7. Glazing material is measured accurately to minimise waste and within specified tolerances according to workplace standards
- 2.8. Components and controls of machines, including emergency stops and guards are identified and tested for working order
3. Cut glazing materials
- 3.1. Tools and equipment are operated and monitored in accordance with manufacturers' instructions and workplace procedures to ensure correct product quality and output
- 3.2. Glazing material is processed to required standard in accordance with job order, work instructions and procedures, including the performance of routine lubrication and adjustments of machines/equipment
- 3.3. Problems occurring during work operations are identified and reported to appropriate persons
- 3.4. Authorised changes in working procedures are followed
4. Complete work
- 4.1. Completed product is inspected for quality of work and repaired, reprocessed or discarded in accordance with workplace procedures
- 4.2. Cut glazing material is labelled and stored following workplace procedures
- 4.3. Scraps and off-cuts are removed for disposal/recycling as required
- 4.4. Work area is cleaned and rubbish disposed of as appropriate
- 4.5. Workplace documentation is completed as required
- 4.6. Tools, equipment and unused materials are removed and stored appropriately
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit scope
This unit addresses the work involved in cutting and handling glazing materials used in picture framing
Unit context
OHS requirements may include legislation, material safety management systems and local safe operating procedures
Work is carried out in accordance with statutory requirements, environment legislation, manual handling procedures and relevant regulations and organisation insurance requirements
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the planning, preparation and cutting and handling glazing materials
Glazing materials include, but are not limited to:
plain sheet glass
speciality glass
non-glare glass
UV clear glass
UV non-glare glass
sheet acrylic
conservation acrylic
mirrors
Tools and equipment are to include:
flat felt-covered cutting tables
tungsten wheel glass cutters
wall-mounted glass cutters
saws
scoring tools
speed cutters
T-squares or L-squares
tape measures
marking pens or chinagraph pencils
templates and lubricants
Personal protection equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices. It could include:
gloves
safety glasses and footwear
aprons and overalls
Information and procedures
Workplace procedures relating to the use and operation of tools and equipment required for the handling and cutting of glazing materials
Workplace instructions, including job sheets, cutting lists, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer instructions for the use of equipment and materials
Quality standards and procedures
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit scope
This unit addresses the work involved in cutting and handling glazing materials used in picture framing
Unit context
OHS requirements may include legislation, material safety management systems and local safe operating procedures
Work is carried out in accordance with statutory requirements, environment legislation, manual handling procedures and relevant regulations and organisation insurance requirements
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the planning, preparation and cutting and handling glazing materials
Glazing materials include, but are not limited to:
plain sheet glass
speciality glass
non-glare glass
UV clear glass
UV non-glare glass
sheet acrylic
conservation acrylic
mirrors
Tools and equipment are to include:
flat felt-covered cutting tables
tungsten wheel glass cutters
wall-mounted glass cutters
saws
scoring tools
speed cutters
T-squares or L-squares
tape measures
marking pens or chinagraph pencils
templates and lubricants
Personal protection equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices. It could include:
gloves
safety glasses and footwear
aprons and overalls
Information and procedures
Workplace procedures relating to the use and operation of tools and equipment required for the handling and cutting of glazing materials
Workplace instructions, including job sheets, cutting lists, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer instructions for the use of equipment and materials
Quality standards and procedures
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects of evidence
Interpret work orders and plan cutting operations
Identify the materials, patterns/plans, processes, machines, equipment and settings to cut glazing materials
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Set up for and prepare to cut glazing materials
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
As a minimum, demonstrate the ability to:
cut 3 pieces of glass to within .05 mm tolerance
cut 3 pieces of acrylic to within .05 mm tolerance
cut 2 pieces of oval glass to within 1.5 mm tolerance
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource implications
Glazing material, cutting equipment, table, work area, work orders, standard work procedures and appropriate safety and personal protection equipment.
Method of assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other units of competency which together form a part of the job role.
Context of assessment
Assessment may occur on the job or in a workplace simulated facility with relevant glazing material cutting equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects of evidence
Interpret work orders and plan cutting operations
Identify the materials, patterns/plans, processes, machines, equipment and settings to cut glazing materials
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Set up for and prepare to cut glazing materials
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
As a minimum, demonstrate the ability to:
cut 3 pieces of glass to within .05 mm tolerance
cut 3 pieces of acrylic to within .05 mm tolerance
cut 2 pieces of oval glass to within 1.5 mm tolerance
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource implications
Glazing material, cutting equipment, table, work area, work orders, standard work procedures and appropriate safety and personal protection equipment.
Method of assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other units of competency which together form a part of the job role.
Context of assessment
Assessment may occur on the job or in a workplace simulated facility with relevant glazing material cutting equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0356 | LMFPF2006A | Cut and handle glazing materials for framing | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI585 | MSFPF2006 | Cut and handle glazing materials for framing | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W026 | LMF20602 | Certificate II in Picture Framing | Qualification |
| W036 | LMF30802 | Certificate III in Picture Framing | Qualification |