Unit of competency Outline

Date retreived
22/07/2026 6:48 AM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Coordinate and direct switching program

Coordinate and direct switching program

Unit of competency
National Code
UEPOPS525
State Code
OAG02
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
31/10/2018
View on TGA
State Implementation and Classification
Approved Date
15/05/2019
Field of Education
031301 - Electrical Engineering
Original Release Date
15/05/2019
Nominal Hours
54
Description
This unit involves the skills and knowledge required to coordinate and direct resources for a switching program.An electricalswitchcan alternate a load between two sources either manually or automatically when sensors detect one of the sources has lost or gained power. A switchis typically installed where the backup generator is located so that the generator can be used to provide temporary electrical power, as required.Competency in this unit requires the ability to prepare for a switching program, coordinate and direct a switching program, maintain dynamic integrity of power generation systemand complete all documentation. Individuals will, in general, work as a switching program coordinator, in a power generation facility.Power generation plant operators are typically trained and authorised to isolate, prepare plant and issue permits to work.No licensing, legislative or certification requirements apply to this unit at the time of publication.Note: Workplace practiceThe application of the skills and knowledge described in this unit may require a licence or training permit to practice in the workplace where work is carried out on gas and electrical installations. Additional conditions may apply under state and territory legislative and regulatory licensing requirements.
Notes
Elements and Performance Criteria
1 Prepare for switching program
  • 1.1 Qualifications and authorisations of personnel performing switching operations are established, in accordance with workplace procedures
  • 1.2 Work, Health and Safety (WHS)/Occupational Health and Safety (OHS) regulations, industry standards, legislative requirements codes of practice and environmental obligations are identified, applied and monitored
  • 1.3 Contingency plan is evaluated and discussed with key stakeholders, in accordance with workplace procedures, and any amendments made are relayed to all appropriate personnel
  • 1.4 Permit and access requirements are established prior to switching program commencement, in accordance with workplace procedures
  • 1.5 Documentation is distributed, in accordance with workplace procedures, to relevant personnel prior to switching program commencement
2 Direct switching program
  • 2.1 Personnel are advised of switching programme and directed to locations, in accordance with workplace procedures
  • 2.2 Communication is established with key stakeholders and personnel, in accordance with workplace procedures, and is maintained throughout duration of switching program
  • 2.3 Network system schematic diagram, or equivalent, is updated, in accordance with workplace procedures, as switching program proceeds
  • 2.4 Access to power generation plant is controlled, in accordance with workplace policies and procedures
  • 2.5 Work groups are coordinated and directed throughout switching programme, in accordance with workplace procedures
  • 2.6 Permits issued are monitored and recorded, in accordance with workplace procedures
  • 2.7 Switching program is controlled, in accordance with workplace procedures, to ensure outage coincides with planned timetable
3 Maintain dynamic integrity of system
  • 3.1 Switching program steps are verified before and after each operation, in accordance with workplace procedures
  • 3.2 Switching program steps are recorded, in accordance with workplace procedures, upon successful completion of each operation
  • 3.3 Network system conditions or stability is constantly monitored, in accordance with workplace procedures
  • 3.4 Alternative switching program steps are quickly and accurately developed, in accordance with workplace procedures, if unexpected problems occur
4 Complete documentation
  • 4.1 Equipment problems and status are reported, in accordance with workplace procedures
  • 4.2 Documentation is updated, in accordance with workplace procedures
No information
No information
Replaces
State Code National Code Title Type
WE449 UEPOPS525A Coordinate and direct switching program Unit of competency
Replaced By
State Code National Code Title Type
ODZ09 UEPOPS022 Coordinate and direct switching program Unit of competency