Unit of competency Outline
Date retreived
22/07/2026 9:44 PM AWST
22/07/2026 9:44 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Undertake pre make-ready for die cutting
Undertake pre make-ready for die cutting
Unit of competency
National Code
ICPCF326C
ICPCF326C
State Code
D3054
D3054
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
09/09/2014
Field of Education
030103 - Printing
Original Release Date
09/09/2014
Nominal Hours
50
Description
This unit describes the performance outcomes, skills and knowledge required to prepare cutting formes (two large and two small) to accommodate different complexities of cutting with multiple images with extremely tight registration and highly accurate cutting requirements.
Notes
Elements and Performance Criteria
1. Obtain job instuctions and locate forme
- 1.1. Job sheets or instructions are interpreted correctly
- 1.2. Existing formes are located in storage area using filing system and new formes and associated tooling are collected from holding location
2. Check cutting forme
- 2.1. Cutting forme/tooling is checked against master sample for accuracy of cut and fold
- 2.2. Centre line is located and checked to ensure accuracy of positioning/registration on Bobst
3. Position and set up counters
- 3.1. Cutting plate is located and prepared for counters
- 3.2. Counters are accurately positioned and set up on cutting plate to ensure registration with cutting forme
4. Conduct sample cut
- 4.1. Material to be used for sample cut is obtained
- 4.2. Cutting forme and cutting plate are accurately positioned on machine
- 4.3. Machine is operated to produce sample according to enterprise procedures
5. Check sample
- 5.1. Sample is accurately cut and registration of tooling is precise
- 5.2. Forme or tooling is adjusted if necessary according to job specifications
- 5.3. Sample is confirmed as correct by supervisor if required
6. Set up stripping forme and blank separator
- 6.1. Pins are positioned on stripping forme to ensure accurate removal of waste board
- 6.2. Blank separator is set up according to job specifications
7. Undertake filing procedure
- 7.1. Correct identification number is allocated to cutting formes/tooling and strippers and recorded
- 7.2. Information is correctly entered into filing system according to enterprise procedures
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Context may include:
this competency is performed between the making of the cutting forme and it going to the cutting machine for normal make ready.
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Context may include:
this competency is performed between the making of the cutting forme and it going to the cutting machine for normal make ready.
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Evidence of the following is essential:
prepare cutting formes (two large and two small) to accommodate different complexities of cutting with multiple images with extremely tight registration and highly accurate cutting requirements
demonstrate an ability to find and use information relevant to the task from a variety of information sources
prepare FOUR cutting formes (two large and two small) to accommodate TWO different complexities of cutting. At least ONE must contain multiple images with extremely tight registration and highly accurate cutting requirements
evidence for assessment may be gathered from assessment of the unit of competency alone or through an integrated assessment activity.
Context of and specific resources for assessment
Assessment must ensure:
assessment may take place on the job, off the job or a combination of these
off the job assessment must be undertaken in a closely simulated workplace environment.
Method of assessment
A range of assessment methods should be used to assess practical skills and knowledge. The following examples are appropriate for this unit:
direct questioning combined with review of portfolios of evidence and third party workplace reports of on-the-job performance by the candidate.
Guidance information for assessment
Holistic assessment with other units relevant to the industry sector, workplace and job role is recommended.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Evidence of the following is essential:
prepare cutting formes (two large and two small) to accommodate different complexities of cutting with multiple images with extremely tight registration and highly accurate cutting requirements
demonstrate an ability to find and use information relevant to the task from a variety of information sources
prepare FOUR cutting formes (two large and two small) to accommodate TWO different complexities of cutting. At least ONE must contain multiple images with extremely tight registration and highly accurate cutting requirements
evidence for assessment may be gathered from assessment of the unit of competency alone or through an integrated assessment activity.
Context of and specific resources for assessment
Assessment must ensure:
assessment may take place on the job, off the job or a combination of these
off the job assessment must be undertaken in a closely simulated workplace environment.
Method of assessment
A range of assessment methods should be used to assess practical skills and knowledge. The following examples are appropriate for this unit:
direct questioning combined with review of portfolios of evidence and third party workplace reports of on-the-job performance by the candidate.
Guidance information for assessment
Holistic assessment with other units relevant to the industry sector, workplace and job role is recommended.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| D0317 | ICPCF326B | Undertake pre make-ready for die cutting | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| AUP11 | ICPCBF326 | Undertake pre make-ready for die cutting | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| J188 | ICP30912 | Certificate III in Printing and Graphic Arts (Cartons and Corrugating) | Qualification |
| J189 | ICP31012 | Certificate III in Printing and Graphic Arts (Mail House) | Qualification |
| J186 | ICP30712 | Certificate III in Printing and Graphic Arts (Print Finishing) | Qualification |