Unit of competency Outline
Date retreived
22/07/2026 2:07 PM AWST
22/07/2026 2:07 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Apply soft rubber techniques
Apply soft rubber techniques
Unit of competency
National Code
LMFFF3004B
LMFFF3004B
State Code
W8517
W8517
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
19/09/2008
Field of Education
030117 - Furniture Polishing
Original Release Date
19/09/2008
Nominal Hours
20
Description
This unit covers the competency to apply polish and/or spirit varnish to surfaces using soft rubber techniques.
Notes
Elements and Performance Criteria
1. Prepare for work
- 1.1. Workplace information, including materials application and safety information, material safety data sheets, is used to inform work practices
- 1.2. Characteristics of the surface and the required surface finish are identified from work orders or instructions
- 1.3. Processing and application techniques, time and safety requirements are identified and used for work planning
- 1.4. OHS requirements, including ventilation requirements and personal protection needs, are observed throughout the work
- 1.5. Tools, equipment and accessories are identified and checked for safe and effective operation for the surface finishing task
2. Prepare for application of materials
- 2.1. Surfaces are checked for contamination and correct preparation according to workplace procedures and standards
- 2.2. Products with surface or other faults are identified and faults repaired as appropriate
- 2.3. Finishing materials required are identified and prepared for the task
- 2.4. Trial applications of surface materials are made to check rubber operation, materials consistency and specified surface finish
- 2.5. Faults are identified and workplace procedures for rectification are followed
3. Apply soft varnish/rubber
- 3.1. Surface is lightly sanded and checked for defects which are rectified in accordance with workplace procedures
- 3.2. Rubber is suitably charged
- 3.3. Surface is soft-rubbered/varnish rubbered using correct amount of pressure and suitable rubber movements
- 3.4. Surface is inspected and any defects repaired/rectified
4. Clean work area and maintain equipment
- 4.1. Equipment used is cleaned and inspected for serviceable condition and stored appropriately
- 4.2. Unserviceable equipment is tagged, faults are identified and appropriate personnel are informed
- 4.3. Work area is cleaned and returned to approved condition
- 4.4. Workplace records are completed
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the application of soft rubber techniques
Soft rubbers
Soft rubbers consist of cotton-wool or wadding body wrapped in cotton cloth and are used for either polish or varnish
Surfaces my include but are not limited to:
solid timber and manufactured board
Tools and equipment may include, but are not limited to:
brushes
swooges
soft rubbers and sanding blocks
Materials may include but are not limited to:
polish
methylated spirits
spirit varnish
scourer
abrasive papers
cotton rags
steel wool
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturer specifications and operational procedures
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the application of soft rubber techniques
Soft rubbers
Soft rubbers consist of cotton-wool or wadding body wrapped in cotton cloth and are used for either polish or varnish
Surfaces my include but are not limited to:
solid timber and manufactured board
Tools and equipment may include, but are not limited to:
brushes
swooges
soft rubbers and sanding blocks
Materials may include but are not limited to:
polish
methylated spirits
spirit varnish
scourer
abrasive papers
cotton rags
steel wool
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturer specifications and operational procedures
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Accurately apply soft/varnish rubber techniques on a minimum of two occasions which must cover a chair or equivalent, and a large flat surface
Maintain application equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Soft rubber materials, coating materials, other consumables and surfaces to be coated.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment may be in conjunction with other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Accurately apply soft/varnish rubber techniques on a minimum of two occasions which must cover a chair or equivalent, and a large flat surface
Maintain application equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Soft rubber materials, coating materials, other consumables and surfaces to be coated.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment may be in conjunction with other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0264 | LMFFF3004A | Apply soft rubber techniques | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI324 | MSFFF3004 | Apply soft rubber techniques | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W030 | LMF30202 | Certificate III in Furniture Finishing | Qualification |