Unit of competency Outline

Date retreived
22/07/2026 7:56 AM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Conduct large diameter auger drilling

Conduct large diameter auger drilling

Unit of competency
National Code
RIINHB306D
State Code
WH475
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
2.00
Current Release Date
07/12/2014
View on TGA
State Implementation and Classification
Approved Date
29/05/2014
Field of Education
030303 - Mining Engineering
Original Release Date
29/05/2014
Nominal Hours
60
Description
This unit describes a participant’s skills and knowledge required to conduct large diameter auger drilling in Civil construction and Drilling. This unit is appropriate for those working in operational roles.No licensing, legislative or certification requirements apply to this unit at the time of publication
Notes
Elements and Performance Criteria
1. Plan and prepare for large diameter auger drilling
  • 1.1 Access, interpret and apply conduct large diameter auger drilling apply documentation, and the work activity is compliant
  • 1.2 Obtain, read, interpret, clarify and confirm work requirements
  • 1.3 Identify and address potential risks, hazards and environmental issues and implement control measures
  • 1.4 Select and wear personal protective equipment appropriate for work activities
  • 1.5 Communicate and coordinate activities with others throughout the work activity
  • 1.6 Obtain and interpret emergency procedures, and be prepared for fire/accident/emergency
2. Operate large diameter auger drill
  • 2.1 Carry out pre-start and start up procedures
  • 2.2 Identify, select and apply rig operational controls
  • 2.3 Collar borehole, start hole, maintain hole alignment, take corrective action for deflections
  • 2.4 Make up appropriate drill string
  • 2.5 Handle additional drill stems, inserting them in the drill string
  • 2.6 Use appropriate gears, rotation, feed and holdback so that flights or bucket are substantially full for the soil being drilled at any given depth
  • 2.7 Interpret drilling factors to determine conditions at the bit
  • 2.8 Make and break auger string and drive head connections
  • 2.9 Maintain a clear hole and a clear bottom and deploy tools for cleaning hole bottom at completed depth
  • 2.10 Interpret or calculate actual depth at any point during drilling, interpret depth of strata changes and identify fill depth in any bore
  • 2.11 Select appropriate strategies for recovery of dropped augers
  • 2.12 Recover drill string using winch and/or head/kelly
  • 2.13 Insert surface casing and deepen hole using smaller diameter auger or bucket, if required
  • 2.14 Disassemble drill string and change augers and bit components
  • 2.15 Select bits for formation being drilled
  • 2.16 Select appropriate augering method for situation
  • 2.17 Maintain spoil removal from hole collar
  • 2.18 Cover and secure bores
  • 2.19 Prepare and submit paperwork for daily activities
  • 2.20 Continually monitor hazards and risks , and ensure safety of self, other personnel, plant and equipment
  • 2.21 Select and use water and drilling fluids as appropriate
  • 2.22 Bell foundation piles, if required
  • 2.23 Clean pile bases and insert reinforcement cages, if required
  • 2.24 Deploy bucket augers through surface casing and when drilling under bentonite muds
  • 2.25 Use spin off and side casting of spoil as appropriate
  • 2.26 Record daily hole depths and progress
3. Respond to problems
  • 3.1 Identify possible operational problems in equipment or process
  • 3.2 Identify symptoms of problems needing remedial action
  • 3.3 Determine possible fault causes
  • 3.4 Rectify problem using appropriate solution within area of responsibility
  • 3.5 Follow through items initiated until final resolution has occurred
  • 3.6 Report problems outside area of responsibility to designated person
4. Complete equipment maintenance and housekeeping
  • 4.1 Carry out shutdown and secure equipment
  • 4.2 Monitor external wear in drill string, rotate string elements to ensure even wear
  • 4.3 Interchange drill bits and/or drill bit elements to maintain free cutting ability
  • 4.4 Check all string and equipment elements for wear and proper function
  • 4.5 Replace worn elements in string, bits and equipment and recycle ‘out of specification’ equipment for repair or redundancy
  • 4.6 Apply lubrication as appropriate
  • 4.7 Ensure housekeeping activities are completed
  • 4.8 Process records
No information
No information
Replaced By
State Code National Code Title Type
AWB97 RIINHB306E Conduct large diameter auger drilling Unit of competency
State Code National Code Title Type
J633 RII31813 Certificate III in Drilling Operations Qualification