Unit of competency Outline
Date retreived
22/07/2026 7:17 PM AWST
22/07/2026 7:17 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Construct furniture using leg and rail method
Construct furniture using leg and rail method
Unit of competency
National Code
LMFFM3002B
LMFFM3002B
State Code
W8611
W8611
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
03/11/2009
Field of Education
030113 - Cabinet Making
Original Release Date
03/11/2009
Nominal Hours
40
Description
This unit covers the competency to follow plans to construct and assemble furniture using leg and rail construction
Notes
Elements and Performance Criteria
1. Prepare for work
- 1.1. Work instructions are used to determine job requirements, including design, tolerances, process, materials, finish and quantity
- 1.2. Construction and assembly sequence are planned
- 1.3. Procedures are determined for checking quality at each stage of the process
- 1.4. Workplace health and safety requirements, including personal protection needs, are observed throughout the work
- 1.5. Suitable work area is selected for the task
- 1.6. Preparatory drawings/set-outs/rods for tasks are completed
- 1.7. Cutting list for components is developed
- 1.8. Materials are selected following work instructions
- 1.9. Tools and equipment suitable for construction are identified and checked for safe and effective operation
2. Complete construction
- 2.1. Material is set out and prepared according to work instructions and components are marked according to workplace procedures
- 2.2. Tools, machines and equipment are used in accordance with safety requirements and manufacturers' specifications
- 2.3. Components are manufactured, including any specified shapes, angles or curves and checked against set-outs and job requirements
- 2.4. Components are assembled using jigs and/or clamps and fastenings
- 2.5. Adhesives are applied according to workplace procedures and/or manufacturers' instructions
- 2.6. Joining process is undertaken according to workplace procedures
- 2.7. Assembled furniture is checked for compliance with specifications
- 2.8. Furniture is finished to suitable state for surface preparation
- 2.9. Any non-conformity with the required quality standards is rectified
3. Finalise operation
- 3.1. Faulty and/or defective equipment is tagged and reported in accordance with workplace practices
- 3.2. Work area is cleaned, hand and/or power tools and equipment are cleaned, maintained and stored in accordance with workplace procedures
- 3.3. Off-cuts and unused materials are collected and stored for reuse or disposed following workplace procedures
- 3.4. Waste and scrap materials are dealt with following workplace procedures
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Furniture to be constructed using the leg and rail method may include:
dining
occasional
hall and side tables
dining and occasional chairs
and cabinets
Unit context
OH&S requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Competency may be demonstrated in workplaces involved in the manufacture of solid timber furniture, domestic furniture, commercial furniture, kitchen and bathroom cabinets and/or furniture components
Unit scope
Work involves reading and interpreting plans, developing set-outs, using static machines, using hand and power tools to construct furniture using traditional jointing methods (mortise and tenon, mitre, dowel and bridle)
Tools and equipment may include, but are not limited to:
measuring tapes or rulers
hammers
mallets
squares
bevels
chisels
planes
hand saws
power saws
cordless drills/screwdrivers
power drills
fixing and jointing devices
pneumatic tools
jigs
clamps and pincers
Machines may include, but are not limited to:
band saws
cross cut saws
jig saws
panel and rip saws
surface planers
panel planers
belt sanders
horizontal borers
vertical drill presses
furniture mortise and tenoner
dovetailers
pedestal grinders
wood turning lathes
veneer guillotines and presses
Materials to be used may include but are not limited to:
timber
manufactured board
adhesives
screws
nails
dowels
knock down fittings
Checking of constructed product is to cover:
squareness
parallel
twist
and distortion and product faults
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, cutting lists, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturers' specifications and operational procedures
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Furniture to be constructed using the leg and rail method may include:
dining
occasional
hall and side tables
dining and occasional chairs
and cabinets
Unit context
OH&S requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Competency may be demonstrated in workplaces involved in the manufacture of solid timber furniture, domestic furniture, commercial furniture, kitchen and bathroom cabinets and/or furniture components
Unit scope
Work involves reading and interpreting plans, developing set-outs, using static machines, using hand and power tools to construct furniture using traditional jointing methods (mortise and tenon, mitre, dowel and bridle)
Tools and equipment may include, but are not limited to:
measuring tapes or rulers
hammers
mallets
squares
bevels
chisels
planes
hand saws
power saws
cordless drills/screwdrivers
power drills
fixing and jointing devices
pneumatic tools
jigs
clamps and pincers
Machines may include, but are not limited to:
band saws
cross cut saws
jig saws
panel and rip saws
surface planers
panel planers
belt sanders
horizontal borers
vertical drill presses
furniture mortise and tenoner
dovetailers
pedestal grinders
wood turning lathes
veneer guillotines and presses
Materials to be used may include but are not limited to:
timber
manufactured board
adhesives
screws
nails
dowels
knock down fittings
Checking of constructed product is to cover:
squareness
parallel
twist
and distortion and product faults
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, cutting lists, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturers' specifications and operational procedures
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment and products
maintain required production output and product quality
Construct a minimum of two furniture products which are to include:
a table with a drawer, and
a chair with shaped and angled components
and require the jointing processes listed in the Range Statement
Work effectively with others
Modify activities to cater for variations in workplace context and environment
Resource Implications
Access to plans, hand and/or power tools, equipment, woodworking machinery, materials, and a work area.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment and products
maintain required production output and product quality
Construct a minimum of two furniture products which are to include:
a table with a drawer, and
a chair with shaped and angled components
and require the jointing processes listed in the Range Statement
Work effectively with others
Modify activities to cater for variations in workplace context and environment
Resource Implications
Access to plans, hand and/or power tools, equipment, woodworking machinery, materials, and a work area.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0285 | LMFFM3002A | Construct furniture using leg and rail method | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI423 | MSFFM3002 | Construct furniture using leg and rail method | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W651 | LMF32109 | Certificate III in Cabinet Making | Qualification |
| W031 | LMF30302 | Certificate III in Furniture Making | Qualification |
| W032 | LMF30402 | Certificate III in Furniture Making (Cabinet Making) | Qualification |
| W033 | LMF30502 | Certificate III in Furniture Making (Wood Machining) | Qualification |
| W035 | LMF30702 | Certificate III in Mattress and Base Making | Qualification |