Unit of competency Outline
Date retreived
22/07/2026 9:01 AM AWST
22/07/2026 9:01 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Assemble mattress components
Assemble mattress components
Unit of competency
National Code
LMFMB2003B
LMFMB2003B
State Code
W8700
W8700
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
19/09/2008
Field of Education
030115 - Furniture Upholstery And Renovation
Original Release Date
19/09/2008
Nominal Hours
40
Description
This unit covers the competency to assemble specified mattresses, including the planning of work, selection of fabrics and components and the assembly of the components
Notes
Elements and Performance Criteria
1. Plan work operations
- 1.1. Specifications concerning design, fabrics and finish are confirmed with designer/client, as required
- 1.2. Workplace health and safety requirements, including ergonomic criteria and personal protection needs, are observed throughout the work
- 1.3. Suitable work area is selected, tidied and cleaned of any contaminants
- 1.4. Appropriate equipment and tools are selected and checked for the required fitting and assembly process
2. Select and inspect fabrics and components
- 2.1. Fabric panels are checked in terms of quantity, quality, contaminants, size, pattern and consistency
- 2.2. Grade of foam is selected and checked in accordance with work order
- 2.3. Appropriate padding and springs are selected and checked
3. Assemble components and fit fabric cover
- 3.1. Work pieces are laid out in sequence according to specifications, construction process and workplace procedures
- 3.2. Padding and underlay materials are attached to spring unit using appropriate enterprise techniques and equipment
- 3.3. Covering fabrics are applied to mattress ensuring:
- 3.4. Patterns, naps, sheens, direction of pattern, pattern repeat and finished side of the materials are positioned appropriate to the design
- 3.5. Fabric finish over the spring unit is smooth and consistent
- 3.6. Weaving lines are straight
- 3.7. Finish of applied fabric is checked against quality standards
4. Clean work area/s and maintain equipment
- 4.1. Faulty and/or defective equipment is tagged and reported in accordance with workplace OHS procedures
- 4.2. Waste and scrap is removed following workplace procedures
- 4.3. Tools and equipment used are cleaned, inspected for serviceable condition and stored appropriately in accordance with workplace procedures
- 4.4. Equipment and work area clean-up is maintained in accordance with workplace procedures
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit scope
This unit covers work involving the assembly of components to produce mattresses
Materials and components may include but are not limited to:
spring units
plain and patterned fabric
padding materials
foam
Unit context
Work is carried out in accordance with statutory requirements, organisation insurance requirements, OHS legislation, environmental legislation, manual handling procedures and relevant health regulations
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the assembly of mattress components
Work may be performed in workplaces which are involved in the manufacture or restoration of mattresses and base units
Tools and equipment may include, but are not limited to:
glues
staples
buttons
scissors
measuring and marking equipment
staple lifters
pliers
trimming knife
needles
spring benders
clip guns
staple guns
glue guns
long tom
foam cutter
fabric cutter
sewing machines
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use and operations of tools
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit scope
This unit covers work involving the assembly of components to produce mattresses
Materials and components may include but are not limited to:
spring units
plain and patterned fabric
padding materials
foam
Unit context
Work is carried out in accordance with statutory requirements, organisation insurance requirements, OHS legislation, environmental legislation, manual handling procedures and relevant health regulations
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the assembly of mattress components
Work may be performed in workplaces which are involved in the manufacture or restoration of mattresses and base units
Tools and equipment may include, but are not limited to:
glues
staples
buttons
scissors
measuring and marking equipment
staple lifters
pliers
trimming knife
needles
spring benders
clip guns
staple guns
glue guns
long tom
foam cutter
fabric cutter
sewing machines
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use and operations of tools
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects of evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Identify and select materials used and any special handling requirements for those materials
Assemble mattress components to construct at least the following:
one pillow top mattress
one standard sprung mattress
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource implications
Appropriate equipment and tools, plain and patterned fabrics, padding materials, spring units, fixing materials and tools, work order, workplace information, including work procedures and equipment instructions.
Method of assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and will generally be in conjunction with assessment of other units of competency.
Context of assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects of evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Identify and select materials used and any special handling requirements for those materials
Assemble mattress components to construct at least the following:
one pillow top mattress
one standard sprung mattress
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource implications
Appropriate equipment and tools, plain and patterned fabrics, padding materials, spring units, fixing materials and tools, work order, workplace information, including work procedures and equipment instructions.
Method of assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and will generally be in conjunction with assessment of other units of competency.
Context of assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0344 | LMFMB2003A | Assemble mattress components | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI573 | MSFMB2002 | Assemble mattress components | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W035 | LMF30702 | Certificate III in Mattress and Base Making | Qualification |
| W025 | LMF20502 | Certificate II in Mattress and Base Making | Qualification |