Unit of competency Outline
Date retreived
22/07/2026 5:31 AM AWST
22/07/2026 5:31 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Maintain cathodic protection systems
Maintain cathodic protection systems
Unit of competency
National Code
UTGNGS308B
UTGNGS308B
State Code
M2041
M2041
TGA Status
Replaced
Replaced
DTWD Status
Archived
Archived
State Implementation and Classification
Approved Date
25/09/2003
Field of Education
040327 - Plumbing
Original Release Date
25/09/2003
Nominal Hours
80
Description
Notes
Elements and Performance Criteria
No information
Types of CP faults may include coating damage/deterioration; interference from other systems; anode not working; equipment fault/failure
Applicable Australian Standards/legislation relevant to CP System may include OH&S legislation; utility codes and standards; AS 2885; AS 2430 - hazardous areas; AS 1768; AS 1596; AS 1697; AS 2832.1; AS 3000; AS 2239; AG 603
Location for maintaining CP Systems may be urban, country or remote. Third party monitoring.
Electrical equipment may include solar powered power generation systems; 240 volt power generation systems; insulation and monolithic joints; galvanic anode beds; battery banks - nicad and lead acid; transformer rectifiers and CPUs; lightning protection equipment; CP test points; Kirk cells
Types of checks and tests on CP systems may include on potential surveys; on/off potential surveys; coating defect assessment surveys (DCVG method, Pearson technique/method, over pipeline potential method); loop impedance testing; anode bed testing; soil resistivity testing; interference testing.
Test equipment may include reference half cells; multimeters; dataloggers; trycorders; syncorders; interruptors; CDA equipment; soil resistivity test equipment.
The use of personal computers, other hardware mediums and associated software may be required.
Applicable Australian Standards/legislation relevant to CP System may include OH&S legislation; utility codes and standards; AS 2885; AS 2430 - hazardous areas; AS 1768; AS 1596; AS 1697; AS 2832.1; AS 3000; AS 2239; AG 603
Location for maintaining CP Systems may be urban, country or remote. Third party monitoring.
Electrical equipment may include solar powered power generation systems; 240 volt power generation systems; insulation and monolithic joints; galvanic anode beds; battery banks - nicad and lead acid; transformer rectifiers and CPUs; lightning protection equipment; CP test points; Kirk cells
Types of checks and tests on CP systems may include on potential surveys; on/off potential surveys; coating defect assessment surveys (DCVG method, Pearson technique/method, over pipeline potential method); loop impedance testing; anode bed testing; soil resistivity testing; interference testing.
Test equipment may include reference half cells; multimeters; dataloggers; trycorders; syncorders; interruptors; CDA equipment; soil resistivity test equipment.
The use of personal computers, other hardware mediums and associated software may be required.
Critical aspects of evidence
Interpreting cathodic protection data system surveys and readings; locating and repairing faults; procedures for coating surveys; checking and maintaining potentials
Context of assessment
Assessment of competency, including attainment of relevant knowledge and skills may be made through practical demonstration in an actual work environment or simulation of such an environment.
Specialised resources required for training and assessment
Appropriate equipment required to maintain CP systems; availability of suitably qualified industry assessors; system which facilitates recording of trainees' profiles and progress; facilities for workplace or simulated environment assessment
Pre-requisites and co-requisite
This unit requires, as an entry, attainment of the Certificate II in Gas Operations and related units of competence.
Entry may also be accepted from those who have achieved an equivalent AQF level two-qualification competency outcome. As such, they would be expected to have attained sufficient relevant underpinning knowledge and skills which could be used to accelerate their progress through this unit to the Certificate III in Gas Operations. However, should this not be the case a suitable bridging program is to form part of the entry requirement.
Additionally, this unit should be assessed in conjunction with or after competency has been demonstrated in UTG NGS 309 A Install Cathodic Protection Systems, the Electrotechnology Units UTE NES 204 Install Wiring Systems (Extra Low Voltage) and UTE NES 205 Install Electrical /Electronic Apparatus (Extra Low Voltage) and the following Frontline Management III Competency Standards:
(BSXFM 1301 A) Manage Personal Work Priorities and Professional Development
(BSXFM 1302 A) Provide Leadership in the Workplace
(BSXFM 1303 A) Establish and Manage Effective Workplace Relationships and,
(BSXFM 1308 A) Develop and Maintain a Safe Workplace and Environment
Knowledge and Skills
The Evidence Guide is a set of guidelines which assist in the development of assessment instruments/tools to assess the competency of workers in the Gas Industry. This requires evidence of consistent achievement of the workplace outcomes covered by the unit.
An employee working at this level is required to demonstrate an awareness of the corrosion process; use current technology to record, analysis and interpret data; interpret system design, planning and operation; use the CP System in relation to other services; undertake basic electrical measurement /adhere to electrical principles; demonstrate an understanding of coating requirements and their purpose; obtain relevant permits as required; adhere to OH&S and emergency procedures; select and use appropriate tools and equipment; understand and adhere to SOPs including recording and maintaining accurate records; interpret topographical and geographical maps
Interpreting cathodic protection data system surveys and readings; locating and repairing faults; procedures for coating surveys; checking and maintaining potentials
Context of assessment
Assessment of competency, including attainment of relevant knowledge and skills may be made through practical demonstration in an actual work environment or simulation of such an environment.
Specialised resources required for training and assessment
Appropriate equipment required to maintain CP systems; availability of suitably qualified industry assessors; system which facilitates recording of trainees' profiles and progress; facilities for workplace or simulated environment assessment
Pre-requisites and co-requisite
This unit requires, as an entry, attainment of the Certificate II in Gas Operations and related units of competence.
Entry may also be accepted from those who have achieved an equivalent AQF level two-qualification competency outcome. As such, they would be expected to have attained sufficient relevant underpinning knowledge and skills which could be used to accelerate their progress through this unit to the Certificate III in Gas Operations. However, should this not be the case a suitable bridging program is to form part of the entry requirement.
Additionally, this unit should be assessed in conjunction with or after competency has been demonstrated in UTG NGS 309 A Install Cathodic Protection Systems, the Electrotechnology Units UTE NES 204 Install Wiring Systems (Extra Low Voltage) and UTE NES 205 Install Electrical /Electronic Apparatus (Extra Low Voltage) and the following Frontline Management III Competency Standards:
(BSXFM 1301 A) Manage Personal Work Priorities and Professional Development
(BSXFM 1302 A) Provide Leadership in the Workplace
(BSXFM 1303 A) Establish and Manage Effective Workplace Relationships and,
(BSXFM 1308 A) Develop and Maintain a Safe Workplace and Environment
Knowledge and Skills
The Evidence Guide is a set of guidelines which assist in the development of assessment instruments/tools to assess the competency of workers in the Gas Industry. This requires evidence of consistent achievement of the workplace outcomes covered by the unit.
An employee working at this level is required to demonstrate an awareness of the corrosion process; use current technology to record, analysis and interpret data; interpret system design, planning and operation; use the CP System in relation to other services; undertake basic electrical measurement /adhere to electrical principles; demonstrate an understanding of coating requirements and their purpose; obtain relevant permits as required; adhere to OH&S and emergency procedures; select and use appropriate tools and equipment; understand and adhere to SOPs including recording and maintaining accurate records; interpret topographical and geographical maps
No information
| State Code | National Code | Title | Type |
|---|---|---|---|
| M114 | UTG30198 | Certificate III in Gas Operations | Qualification |