Unit of competency Outline
Date retreived
22/07/2026 4:45 AM AWST
22/07/2026 4:45 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Apply stains, fillers and bleach
Apply stains, fillers and bleach
Unit of competency
National Code
LMFFF2007B
LMFFF2007B
State Code
W8512
W8512
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
19/09/2008
Field of Education
030117 - Furniture Polishing
Original Release Date
19/09/2008
Nominal Hours
56
Description
This unit covers the competency to apply stains, fillers and bleach to timber surfaces.
Notes
Elements and Performance Criteria
1. Prepare for work
- 1.1. Workplace information, including materials application and safety information, material safety data sheets, is used to inform work practices
- 1.2. Characteristics of the surface and the required surface treatment are identified from work orders or instructions
- 1.3. Processing and application techniques, time and safety requirements are identified and used for work planning
- 1.4. OHS requirements, including ventilation requirements and personal protection needs, are observed throughout the work
- 1.5. Tools, equipment and accessories are identified and checked for safe and effective operation for the staining, filling or bleaching task
2. Prepare for application of materials
- 2.1. Surfaces are checked for contamination and correct preparation according to workplace procedures and standards
- 2.2. Products with surface or other faults are identified and faults repaired as appropriate
- 2.3. Materials required to stain and fill in are identified and prepared for the task
- 2.4. Trial applications of stains and or fillers are made to check equipment operation, materials consistency, viscosity and specified colour
- 2.5. Faults and or inconsistencies in colour are identified and workplace procedures for rectification and adjustment are followed
- 2.6. Materials required for bleaching are identified and labelled to prevent cross-contamination of bulk material during application
3. Apply finishing materials
- 3.1. Techniques for application of stain, filler or bleach are identified
- 3.2. Materials are applied according to job instructions, material manufacturers' specifications and workplace procedures
- 3.3. Bleached items are appropriately stored for drying
- 3.4. Finished products are inspected and approved for suitability for further processing
- 3.5. Products which do not meet quality specifications are restrained, filled, bleached or tagged for further investigation.
4. Clean work area and maintain equipment
- 4.1. Equipment used is cleaned and inspected for serviceable condition and stored appropriately
- 4.2. Unserviceable equipment is tagged, faults are identified and appropriate personnel are informed
- 4.3. Bleaching materials are disposed of in accordance with environmental concerns and workplace procedures. Unused material must not be returned to bulk stock
- 4.4. Work area is cleaned and returned to approved condition, all areas used for bleaching are washed down with water
- 4.5. Workplace records are completed
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
Workplace health and safety requirements include OHS legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the application of stains, fillers and bleach
Stains are to include:
lacquer-based wiping stain and spirit-based and may include: water and oil-based
Fillers are to include:
oil-based
water-based and plastic (one-pot) filler
Bleach is to include:
two-solution bleach and may include oxalic acid bleach
Surfaces
Surfaces include solid timber and manufactured board
Tools and equipment may include, but are not limited to:
liquid containers
rubber gloves
face masks
spray booths
spray guns
compressor
air lines
brushes
sanding block
Materials to be applied may include but are not limited to:
stains
fillers
bleaches
water
abrasive papers
cotton rags and hessian
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturer specifications and operational procedures
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
Workplace health and safety requirements include OHS legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the application of stains, fillers and bleach
Stains are to include:
lacquer-based wiping stain and spirit-based and may include: water and oil-based
Fillers are to include:
oil-based
water-based and plastic (one-pot) filler
Bleach is to include:
two-solution bleach and may include oxalic acid bleach
Surfaces
Surfaces include solid timber and manufactured board
Tools and equipment may include, but are not limited to:
liquid containers
rubber gloves
face masks
spray booths
spray guns
compressor
air lines
brushes
sanding block
Materials to be applied may include but are not limited to:
stains
fillers
bleaches
water
abrasive papers
cotton rags and hessian
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturer specifications and operational procedures
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Context of, and specific resources for assessment
Method of assessment
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Context of, and specific resources for assessment
Method of assessment
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0259 | LMFFF2007A | Apply stains, fillers and bleach | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI319 | MSFFF2007 | Apply stains, fillers and bleach | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W030 | LMF30202 | Certificate III in Furniture Finishing | Qualification |
| W022 | LMF20202 | Certificate II in Furniture Finishing | Qualification |