Unit of competency Outline

Date retreived
22/07/2026 9:53 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Maintain light aircraft pneumatic systems

Maintain light aircraft pneumatic systems

Unit of competency
National Code
MEAMEC0043
State Code
OEG71
TGA Status
Current
DTWD Status
Approved
Current Release Number
1.00
Current Release Date
22/11/2022
View on TGA
State Implementation and Classification
Approved Date
28/03/2023
Field of Education
031503 - Aircraft Maintenance Engineering
Original Release Date
28/03/2023
Nominal Hours
70
Description
This unit describes the skills and knowledge required to apply hand skills and use system/component knowledge and applicable maintenance publications and test equipment to inspect, test, troubleshoot and replace components of light aircraft pneumatic systems during the performance of scheduled or unscheduled maintenance. Maintenance may be performed individually or as part of a team.This unit applies to light aircraft that have pneumatic systems where the air source is other than gas turbine engine bleed air. Bleed-air supplied pneumatic systems are covered by units MEA303 Remove and install aircraft pneumatic system components and MEA310 Inspect, test and troubleshoot aircraft pneumatic systems and components.The unit is used in workplaces that operate under the airworthiness regulatory systems of the Civil Aviation Safety Authority (CASA) and the Defence Aviation Safety Authority (DASA).Any other relevant legislation, industry standards and codes of practice within Australia must be applied.
Notes
Elements and Performance Criteria
1. Inspect light aircraft pneumatic systems
  • 1.1 Use maintenance documentation and modification status, including system defect reports, where relevant, to identify specific inspection requirements
  • 1.2 Check isolation tags and configure aircraft for safe system inspection and operation in accordance with the applicable maintenance manual
  • 1.3 Visually or physically check components of pneumatic systems for external signs of defects in accordance with applicable maintenance manual while observing all relevant work health and safety (WHS) requirements
  • 1.4 Identify and report defects in accordance with standard enterprise procedures
2. Test or adjust light aircraft pneumatic systems and components
  • 2.1 Prepare aircraft and system in accordance with applicable maintenance manual for the application of power or system operation
  • 2.2 Functionally test pneumatic system in accordance with maintenance manual for evidence of serviceability or malfunction
  • 2.3 Perform system adjustment in accordance with maintenance manual
3. Troubleshoot light aircraft pneumatic systems
  • 3.1 Use available information from maintenance documentation, inspection and test results, when required, to assist in fault determination
  • 3.2 Use maintenance manual fault diagnosis guides and logic processes to ensure efficient and accurate troubleshooting to line replacement level
  • 3.3 Obtain specialist advice, when required, to assist with the troubleshooting process
  • 3.4 Locate pneumatic system faults and identify and record the causes of the faults in maintenance documentation, when required, in accordance with standard enterprise procedures
  • 3.5 Determine rectification requirements in accordance with standard enterprise procedures
4. Remove and install light aircraft pneumatic system components
  • 4.1 Render system safe in accordance with the applicable maintenance manual and fit isolation tags, when required, to ensure personnel safety
  • 4.2 Carry out pneumatic system component removal in accordance with the applicable maintenance manual while observing all relevant WHS requirements, including the use of material safety data sheets (MSDSs) and items of personal protective equipment (PPE)
  • 4.3 Complete and process required maintenance documentation
  • 4.4 Tag, seal and pack removed components in accordance with specified procedures
  • 4.5 Check components to be installed to confirm correct part numbers, serviceability and modification status
  • 4.6 Carry out installation in accordance with the applicable maintenance manual
  • 4.7 Complete required maintenance documentation and process in accordance with standard enterprise procedures
No information
No information
Replaces
State Code National Code Title Type
AUE81 MEA354 Maintain light aircraft pneumatic systems Unit of competency
State Code National Code Title Type
BIB7 MEA30222 Certificate III in Aeroskills (Mechatronics) Qualification