Unit of competency Outline

Date retreived
22/07/2026 3:22 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Employ tools, equipment and materials in a shipboard context

Employ tools, equipment and materials in a shipboard context

Unit of competency
National Code
MARC046
State Code
OCH48
TGA Status
Current
DTWD Status
Approved
Current Release Number
2.00
Current Release Date
22/11/2024
View on TGA
State Implementation and Classification
Approved Date
09/04/2021
Field of Education
031701 - Maritime Engineering
Original Release Date
09/04/2021
Nominal Hours
35
Description
Notes
Elements and Performance Criteria
1 Follow safe work practices
  • 1.1 Work health and safety (WHS)/occupational health and safety (WHS/OHS) procedures relevant to using tools and equipment are complied with
  • 1.2 Safety hazards are identified and reported according to safety and vessel procedures
  • 1.3 Prior to use, tools and equipment needed to carry out maintenance activities are checked for correct operation and safety according to safety and vessel procedures
  • 1.4 Before commencing maintenance activities, isolation precautions are implemented according to safety and vessel procedures
2 Carry out heat treatment
  • 2.1 Requirements of job are determined from engineering drawings, job sheet or supervisor
  • 2.2 Heat treatment equipment is selected for required heat treatment according to safety, workplace and manufacturer requirements
  • 2.3 Equipment is set up and used according to standard operating procedures (SOPs) and manufacturer instructions
  • 2.4 Personal protective equipment (PPE) is used according to SOPs
  • 2.5 Emergency procedures are complied with according to approved safety instructions
  • 2.6 Safety signs and symbols are identified and complied with according to approved safety instructions
  • 2.7 Heat treatment process is applied according to job, safety and workplace requirements
  • 2.8 Hazardous conditions are identified, and risk control measures are implemented to maintain a safe work environment
3 Use hand tools
  • 3.1 Hand tools are used according to workplace procedures, WHS/OHS requirements and manufacturer instructions
  • 3.2 Faults with hand tools and equipment are identified and reported to appropriate personnel
4 Use hand power tools
  • 4.1 Hand power tools are used according to workplace procedures, WHS/OHS requirements and manufacturer instructions
  • 4.2 Faults with hand power tools and equipment are identified and reported to appropriate personnel
5 Perform pipe work
  • 5.1 Job requirements are determined from engineering drawings, job sheet or supervisor
  • 5.2 Sequence of operations is determined according to workplace, WHS/OHS and job requirements
  • 5.3 Pipe work is fabricated and joined according to relevant standards and job, safety and workplace requirements
  • 5.4 Pipe work is inspected for defects according to workplace procedures
  • 5.5 Pipe work is installed in specified location without damage or distortion to pipe work, surrounding environment or other services
  • 5.6 Type of filters and strainers in piping systems are identified using relevant engineering drawings and specifications
  • 5.7 Pipe work is tested for compliance with job specification and workplace requirements
6 Use machine tools
  • 6.1 Job requirements are determined from engineering drawings, job sheet or supervisor
  • 6.2 Sequence of operations is determined according to workplace, WHS/OHS and job requirements
  • 6.3 Machine tools are selected according to workplace procedures, WHS/OHS requirements and manufacturer instructions
  • 6.4 Machining operations are performed according to workplace, WHS/OHS and job requirements
  • 6.5 Components are measured in line with workplace, WHS/OHS and job requirements
  • 6.6 Machine is adjusted and maintained according to workplace, safety, manufacturer and job requirements
7 Perform welding and thermal cutting operations
  • 7.1 Job requirements are determined from engineering drawings, job sheet or supervisor
  • 7.2 Materials are prepared for welding using correct tools, equipment, materials and procedures
  • 7.3 Materials are welded using appropriate welding process according to relevant standards and job, safety and workplace requirements
  • 7.4 Joints are welded according to relevant standards and job, safety and workplace requirements
  • 7.5 Oxygen fuel gas cutting torch is used to cut straight lines and curves in mild steel plate up to 10 mm thick according to relevant standards and job, safety and workplace requirements
  • 7.6 Weld is inspected according to relevant standards, and job and workplace requirements
8 Perform soldering operations
  • 8.1 Job requirements are determined from engineering drawings, job sheet or supervisor
  • 8.2 Materials are prepared for soldering using correct tools, equipment, materials and procedures
  • 8.3 Materials are soldered according to relevant standards and job, safety and workplace requirements
  • 8.4 Soldered joints are performed according to relevant standards and job, safety and workplace requirements
  • 8.5 Soldered joints are inspected according to relevant standards and job, and workplace requirements
  • 8.6 Materials are desoldered using correct procedure and minimising damage to materials/components
9 Select and use sealants, adhesives, bonding agents, gaskets and packings
  • 9.1 Job requirements are determined from engineering drawings, job sheet or supervisor
  • 9.2 Gaskets and packings are selected and used according to job requirements and manufacturer/component supplier instructions
  • 9.3 Sealants and adhesives are selected and used according to job requirements and manufacturer/component supplier instructions
  • 9.4 Plastic bonding is performed according to job requirements and manufacturer/component supplier instructions
  • 9.5 Sealants, adhesives, bonding agents, gaskets and packings are stored according to workplace and manufacturer/component supplier instructions
No information
No information
Replaces
State Code National Code Title Type
WH825 MARC018 Employ tools, equipment and materials in a shipboard context Unit of competency