Unit of competency Outline

Date retreived
22/07/2026 6:28 AM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Apply protective coatings (basic)

Apply protective coatings (basic)

Unit of competency
National Code
MEM08014B
State Code
W5394
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
01/12/2005
View on TGA
State Implementation and Classification
Approved Date
18/05/2010
Field of Education
030713 - Metal Casting And Patternmaking
Original Release Date
18/05/2010
Nominal Hours
36
Description
This unit covers spraying pre-treatments and protective coatings not limited to brush, roller and conventional spray equipment, at a basic level.
Notes
Elements and Performance Criteria
1. Determine job requirements
  • 1.1. Work requirements are determined from job sheet, instructions, drawings or visual inspection.
  • 1.2. Required protective coating materials are identified according to job specification.
  • 1.3. Required protective coating application equipment is identified according to job requirements.
  • 1.4. Work site is prepared for application of protective coating.
2. Work piece prepared for application of protective coating
  • 2.1. Surface condition is inspected for readiness for application of protective coating according to specification.
  • 2.2. Unsuitable work pieces/surfaces and fabrication defects are identified and appropriate remedial action or reporting is undertaken in accordance with standard operating procedures.
  • 2.3. Components are masked where protective coating application is not specified.
  • 2.4. Conditions for overspray are identified.
3. Equipment prepared for application of surface coating materials
  • 3.1. Required plant and equipment basic operations are understood.
  • 3.2. Routine maintenance is undertaken on plant and equipment in accordance with standard operating procedures.
  • 3.3. Status/reports are recorded by proforma or orally in accordance with standard operating procedures.
  • 3.4. Conventional coating application equipment is assembled in accordance with equipment requirements and standard operating procedures.
4. Apply single pack coatings
  • 4.1. Coating product type, solvent, uses, mixing procedure, clean-up and safety requirements are identified as appropriate.
  • 4.2. Correct method of determining wet film thickness in accordance with specified dry film is demonstrated.
  • 4.3. Coating material is thinned to suit the application method and to achieve required film thickness.
  • 4.4. Coating is applied using specified application method and standard operating procedures.
  • 4.5. Coating schedules can be outlined for metal and non-metal materials.
  • 4.6. Coating application and curing technique are monitored according to standard operating procedures.
5. Clean and store equipment
  • 5.1. Conventional coating application equipment is cleaned, disassembled and inspected for damage.
  • 5.2. Faulty equipment is recorded and reported to appropriate personnel in accordance with standard operating procedures.
  • 5.3. Coating application equipment is stored in accordance with standard operating procedures.
6. Inspect finish surface
  • 6.1. Surface finish is assessed for profile size differences and uses.
  • 6.2. Coating thickness is determined using appropriate instruments and results are compared with job specifications.
  • 6.3. Total surface is inspected for conformance to specification in accordance with standard operating procedures.
  • 6.4. Inspection results are recorded and reported in accordance with standard operating procedures.
7. Select and maintain personal protective equipment (PPE)
  • 7.1. Appropriate personal protective equipment for coating application is selected according to job requirements and standard operating procedures.
  • 7.2. Personal protective equipment is used appropriately in accordance with manufacturers' specifications and standard operating procedures.
  • 7.3. Ancillary support attachments are identified and used.
  • 7.4. Personal protective equipment is maintained in accordance with manufacturers' specification and standard operating procedures.
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Personal protective equipment
Includes hand protection, full body protection, respirators, air fed hoods and foot protection. Noise and heat protection may also be necessary
EVIDENCE GUIDE
The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
A person who demonstrates competency in this unit must be able to apply protective coatings (basic). Competency in this unit cannot be claimed until all prerequisites have been satisfied.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria, including required knowledge, and be capable of applying the competency in new and different situations and contexts.
Context of and specific resources for assessment
This unit may be assessed on the job, off the job or a combination of both on and off the job. Where assessment occurs off the job, that is the candidate is not in productive work, then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations. The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team. The assessment environment should not disadvantage the candidate.
This unit could be assessed in conjunction with any other units addressing the safety, quality, communication, materials handling, recording and reporting associated with applying protective coatings (basic) or other units requiring the exercise of the skills and knowledge covered by this unit.
Method of assessment
Assessors should gather a range of evidence that is valid, sufficient, current and authentic. Evidence can be gathered through a variety of ways including direct observation, supervisor's reports, project work, samples and questioning. Questioning techniques should not require language, literacy and numeracy skills beyond those required in this unit of competency. The candidate must have access to all tools, equipment, materials and documentation required. The candidate must be permitted to refer to any relevant workplace procedures, product and manufacturing specifications, codes, standards, manuals and reference materials.
Guidance information for assessment
Replaced By
State Code National Code Title Type
OAW04 MEM08014 Apply protective coatings (basic) Unit of competency