Unit of competency Outline
Date retreived
22/07/2026 6:46 PM AWST
22/07/2026 6:46 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Coarse sand timber flooring
Coarse sand timber flooring
Unit of competency
National Code
LMFFL2111A
LMFFL2111A
State Code
W8538
W8538
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
16/06/2009
Field of Education
040321 - Floor Coverings
Original Release Date
16/06/2009
Nominal Hours
20
Description
This unit specifies the outcomes required to coarse sand existing floors using a drum or belt driven sanding machine to grade the surface and remove cupping, ridges, high points or deep scratches and usually involving three passes and the gradual overlapping of each run.
Notes
Elements and Performance Criteria
1. Prepare for the work
- 1.1. Applicable legislative, OHS and organisational requirements relevant to coarse sanding oftimber flooring are verified and complied with
- 1.2. Instructions and/or plans are read and interpreted to identify process required to complete work tasks
- 1.3. Timber flooring is checked for contamination and moisture content
- 1.4. Timber flooring condition is assessed and the extent of floor preparation required to meet job specifications is confirmed
- 1.5. Timber flooring is inspected for suitability for sanding operations and any pre-sanding tasks are completed
- 1.6. Mechanical fixings are removed avoiding damage to equipment and surfaces
- 1.7. Tools, equipment and materials are selected and checked prior to use to ensure that they are appropriate for the work, serviceable and in a safe condition
- 1.8. Sequence of work is planned, including the starting point, to ensure efficiency and quality of installation
2. Conduct coarse sanding operations
- 2.1. Coarse sanding equipment is set up in accordance with manufacturer instructions and operating procedures
- 2.2. Emergency stops, gauges, guards and controls are identified and checked
- 2.3. Equipment settings and adjustments are made and checked
- 2.4. Trial runs are conducted to check machine operations and quality of finished work
- 2.5. Sanding belts or papers are attached, routinely checked and changed as required
- 2.6. Sanding is completes systematically and effectively within the minimum required timeframe
- 2.7. Routine lubrication and adjustments to the equipment are completed as required
- 2.8. Timber flooring is cleared and checked for further processing
3. Edge sanding operations
- 3.1. Edge sanding equipment is set up in accordance with manufacturer instructions and operating procedures
- 3.2. Emergency stops, gauges, guards and controls are identified and checked
- 3.3. Equipment settings and adjustments are made and checked
- 3.4. Sanding papers are selected
- 3.5. Trial runs are conducted to check machine operations and quality of finished work
- 3.6. Sanding papers are attached, routinely checked and changed as required
- 3.7. Edge sanding is completed systematically and effectively within the minimum required timeframe
- 3.8. Routine lubrication and adjustments to the equipment are completed as required
- 3.9. Finished timber flooring is cleaned, inspected and any imperfections are rectified following workplace procedures
4. Complete housekeeping
- 4.1. Unused materials are stored or recycled as required
- 4.2. Tools and equipment are cleaned and stored appropriately
- 4.3. Work area is cleaned and rubbish disposed of appropriately
- 4.4. Workplace documentation is completed
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Legislative requirements
are to be in accordance with applicable legislation from all levels of government that affect organisational operation. Requirements may include but not be limited to award and enterprise agreements, industrial relations, Australian Standards, confidentiality and privacy, OHS, the environment, equal opportunity, anti-discrimination, relevant industry codes of practice, duty of care and heritage
OHS requirements
are to be in accordance with Commonwealth, State or Territory legislation and regulations, organisational safety policies and procedures. Requirements may include but not be limited to the use of personal protective equipment and clothing, fire fighting equipment, First Aid equipment, hazard and risk control and elimination, control of hazardous materials and substances, manual handling including lifting and carrying
Organisational requirements
may include but not be limited to legal, organisational and site guidelines, policies and procedures relating to own role and responsibility, quality assurance, procedural manuals, quality and continuous improvement processes and standards, OHS, emergency and evacuation, ethical standards, recording and reporting, access and equity principles and practices, equipment use, maintenance and storage, environmental management (waste disposal, recycling and re-use guidelines)
Coarse sanding of timber flooring
is to include removal of mechanical fixings, punching of nails, sanding the timber flooring to grade the surface and remove cupping, ridges, high points or deep scratches
Instructions
Workplace procedures relating to the use and operation of tools and equipment
Workplace instructions, instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer instructions for the use of equipment and materials
Mechanical fixings
are to include tacks, nails, staples and screws
Tools and equipment
are to include hammer, scrapers, punches, brooms, vacuums, leads and dust masks
Materials
are to include but are not limited to sanding belts, sanding paper, sanding discs, oil and lubricants
Coarse sanding equipment
is to include split drum and belt floor sanders, edge sander, sanding discs using 24 - 60 grit papers, oil and lubricants
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Legislative requirements
are to be in accordance with applicable legislation from all levels of government that affect organisational operation. Requirements may include but not be limited to award and enterprise agreements, industrial relations, Australian Standards, confidentiality and privacy, OHS, the environment, equal opportunity, anti-discrimination, relevant industry codes of practice, duty of care and heritage
OHS requirements
are to be in accordance with Commonwealth, State or Territory legislation and regulations, organisational safety policies and procedures. Requirements may include but not be limited to the use of personal protective equipment and clothing, fire fighting equipment, First Aid equipment, hazard and risk control and elimination, control of hazardous materials and substances, manual handling including lifting and carrying
Organisational requirements
may include but not be limited to legal, organisational and site guidelines, policies and procedures relating to own role and responsibility, quality assurance, procedural manuals, quality and continuous improvement processes and standards, OHS, emergency and evacuation, ethical standards, recording and reporting, access and equity principles and practices, equipment use, maintenance and storage, environmental management (waste disposal, recycling and re-use guidelines)
Coarse sanding of timber flooring
is to include removal of mechanical fixings, punching of nails, sanding the timber flooring to grade the surface and remove cupping, ridges, high points or deep scratches
Instructions
Workplace procedures relating to the use and operation of tools and equipment
Workplace instructions, instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer instructions for the use of equipment and materials
Mechanical fixings
are to include tacks, nails, staples and screws
Tools and equipment
are to include hammer, scrapers, punches, brooms, vacuums, leads and dust masks
Materials
are to include but are not limited to sanding belts, sanding paper, sanding discs, oil and lubricants
Coarse sanding equipment
is to include split drum and belt floor sanders, edge sander, sanding discs using 24 - 60 grit papers, oil and lubricants
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Comply with legislation, regulations, standards, codes of practice and established safe practices and procedures for coarse sanding timber floors
Interpret work order and locate relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
prevent damage to goods, equipment and products
maintain required production output and product quality
minimise the risk of injury to self and others
Complete a minimum of two timber flooring preparations requiring coarse sanding
Work effectively with others
Modify activities to cater for variations in workplace context and environment
Context of, and specific resources for assessment
The application of competency is to be assessed in the workplace or realistically simulated workplace
Assessment is to occur under standard and authorised work practices, safety requirements and environmental constraints
Assessment of essential underpinning knowledge, other than confirmatory questions, will usually be conducted in an off-site context
Assessment is to comply with relevant regulatory or Australian Standards requirements
The following resources should be made available:
workplace location or simulated workplace
materials and equipment relevant to coarse sanding timber floors
specifications and work instructions
Method of assessment
Assessment must satisfy the endorsed assessment guidelines of the Furnishing Industry Training Package
Assessment methods must confirm consistency and accuracy of performance (over time and in a range of workplace relevant contexts) together with application of underpinning knowledge
Assessment methods must be by direct observation of tasks and include questioning on underpinning knowledge to ensure its correct interpretation and application
Assessment may be applied under project related conditions (real or simulated) and require evidence of process
Assessment must confirm a reasonable inference that competency is able not only to be satisfied under the particular circumstance, but is able to be transferred to other circumstances
Assessment may be in conjunction with assessment of other units of competency
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Comply with legislation, regulations, standards, codes of practice and established safe practices and procedures for coarse sanding timber floors
Interpret work order and locate relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
prevent damage to goods, equipment and products
maintain required production output and product quality
minimise the risk of injury to self and others
Complete a minimum of two timber flooring preparations requiring coarse sanding
Work effectively with others
Modify activities to cater for variations in workplace context and environment
Context of, and specific resources for assessment
The application of competency is to be assessed in the workplace or realistically simulated workplace
Assessment is to occur under standard and authorised work practices, safety requirements and environmental constraints
Assessment of essential underpinning knowledge, other than confirmatory questions, will usually be conducted in an off-site context
Assessment is to comply with relevant regulatory or Australian Standards requirements
The following resources should be made available:
workplace location or simulated workplace
materials and equipment relevant to coarse sanding timber floors
specifications and work instructions
Method of assessment
Assessment must satisfy the endorsed assessment guidelines of the Furnishing Industry Training Package
Assessment methods must confirm consistency and accuracy of performance (over time and in a range of workplace relevant contexts) together with application of underpinning knowledge
Assessment methods must be by direct observation of tasks and include questioning on underpinning knowledge to ensure its correct interpretation and application
Assessment may be applied under project related conditions (real or simulated) and require evidence of process
Assessment must confirm a reasonable inference that competency is able not only to be satisfied under the particular circumstance, but is able to be transferred to other circumstances
Assessment may be in conjunction with assessment of other units of competency
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0187 | LMFFC2004A | Prepare timber sub-floor | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI345 | MSFFL2015 | Coarse sand timber flooring | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W506 | LMF31208 | Certificate III in Flooring Technology | Qualification |