Unit of competency Outline

Date retreived
22/07/2026 9:08 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Apply stains and fillers to timber flooring

Apply stains and fillers to timber flooring

Unit of competency
National Code
MSFFL3028
State Code
WI385
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
10/12/2013
View on TGA
State Implementation and Classification
Approved Date
19/06/2014
Field of Education
040321 - Floor Coverings
Original Release Date
19/06/2014
Nominal Hours
20
Description
This unit of competency covers selecting stains and fillers appropriate for the job, preparing for the work and applying the selected stains and fillers to timber flooring.Licensing, legislative or certification requirements may apply to this unit and relevant state/territory and local government agencies should be consulted to determine any necessary certification or licensing for undertaking flooring work. Access to construction sites requires certification of general induction training specified by the National Code of Practice for Induction for Construction Work (ASCC 2007).
Notes
Elements and Performance Criteria
1 Identify and prepare for work requirements
  • 1.1 Applicable work health and safety (WHS), legislative and organisational requirements relevant to the application of stains and fillers to timber flooring are verified and complied with
  • 1.2 Instructions and/or plans are read and interpreted to identify process required to complete work tasks
  • 1.3 Stain and filling material are selected with regard to durability, longevity, aesthetics, manufacturer recommendations and client expectations
  • 1.4 Selected stain and filler materials are assessed as being compatible with each other, with the surface to be finished, and with manufacturer recommendations
  • 1.5 Tools, equipment and materials are selected and checked prior to use to ensure that they are appropriate for the work, serviceable and in a safe condition
  • 1.6 Products with surface or other faults are identified and faults repaired as appropriate
  • 1.7 Surface to be stained and/or filled is inspected and assessed as being ready for coating with the selected stain/filler
  • 1.8 Work sequence is planned to ensure efficiency and quality of application
  • 1.9 WHS requirements, including isolation, ventilation and other personal protection needs, are observed throughout the work
2 Apply finishing system
  • 2.1 Ventilation is checked before chemical fumes are released, and all WHS requirements are met, including use of personal protective equipment
  • 2.2 Environmental protection regulations are complied with and barrier signs to work area are erected
  • 2.3 Staining and/or filling material is prepared in accordance with manufacturer specifications
  • 2.4 Trial applications of stains and/or fillers are made to check equipment operation, materials consistency, viscosity and specified colour
  • 2.5 Faults and/or inconsistencies in colour are identified and workplace procedures for rectification and adjustment are followed
  • 2.6 Staining and/or filling material is applied in accordance with manufacturer recommendations
  • 2.7 Recommended drying times between coats are observed
  • 2.8 Buffing or sanding between coats, where required, is carried out according to manufacturer recommendations
  • 2.9 Finished products are inspected and approved for suitability for further processing
  • 2.10 Final finish meets the requirements of the job
3 Complete housekeeping
  • 3.1 Unused materials are resealed and stored
  • 3.2 Tools and equipment are cleaned, maintained and stored
  • 3.3 Work area is cleaned and waste material is removed and disposed of safely
  • 3.4 Barriers and signs are removed and stored
  • 3.5 Workplace documentation/reporting is completed
No information
No information
Replaces
State Code National Code Title Type
W8578 LMFFL3407A Apply stains and fillers Unit of competency
Replaced By
State Code National Code Title Type
OAJ36 MSFFL3094 Apply stains and fillers to timber flooring Unit of competency
State Code National Code Title Type
J736 MSF30813 Certificate III in Flooring Technology Qualification