Unit of competency Outline

Date retreived
22/07/2026 3:20 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Perform intermediate rigging

Perform intermediate rigging

Unit of competency
National Code
CPCCRI3013
State Code
OCN09
TGA Status
Current
DTWD Status
Approved
Current Release Number
3.00
Current Release Date
24/12/2024
View on TGA
State Implementation and Classification
Approved Date
01/06/2021
Field of Education
040329 - Scaffolding And Rigging
Original Release Date
01/06/2021
Nominal Hours
40
Description
This unit specifies the skills and knowledge required to use intermediate rigging techniques to move and position loads including cranes and precast tilt-up slabs. It includes load distribution and calculation.It applies to workers who perform rigging duties and who would be expected to take responsibility for organising and completing these tasks with a high degree of self direction.Completion of the general construction induction training program, specified in the Safe Work Australia model Code of Practice: Construction Work, is required by anyone carrying out construction work. Achievement of CPCWHS1001 Prepare to work safely in the construction industry meets this requirement.Licensing, legislative, regulatory or certification requirements apply to this unit of competency in some states and territories. For further information, check with the relevant regulatory authority.
Notes
Elements and Performance Criteria
1 Plan and prepare to perform intermediate rigging.
  • 1.1 Interpret work instructions and associated documentation and clarify requirements with relevant persons.
  • 1.2 Plan all work to comply with relevant legislation, regulations, standards, codes, work health and safety, environmental and workplace requirements.
  • 1.3 Erect required safety signage and barricades and select and fit personal protective equipment (PPE) appropriate for work activities.
2 Select and check intermediate rigging equipment.
  • 2.1 Select resources, materials and equipment in accordance with load charts, and inspect for compliance with work instructions.
  • 2.2 Inspect lifting equipment in accordance with manufacturer and workplace requirements.
  • 2.3 Label, reject and dispose of any lifting equipment identified as inconsistent with manufacturer requirements, to prevent its use in any circumstance.
  • 2.4 Determine and select elevated work platforms and other means of mechanical access systems as specified.
  • 2.5 Install fall arrest equipment with ground level installation.
  • 2.6 Determine and select personnel cartage systems.
3 Connect intermediate rigging equipment.
  • 3.1 Calculate and confirm load mass and load distribution.
  • 3.2 Sling loads to ensure encapsulation of whole load.
  • 3.3 Sling part loads to ensure full encapsulation of a part load.
  • 3.4 Sling whole or part loads to protect loads and secure to prevent uncontrolled movement.
  • 3.5 Attach load steerage lines and use to prevent unnecessary load movement.
4 Move and position loads using intermediate rigging equipment.
  • 4.1 Determine load lifting/shifting order to minimise necessity for double lifts.
  • 4.2 Connect lifting/shifting equipment to load.
  • 4.3 Perform test lift/shift to ensure lift suitability.
  • 4.4 Move load safely to required destination and secure in position in accordance with work instructions and workplace requirements.
  • 4.5 Use standard communication signals to coordinate safe movement of load.
5 Remove intermediate rigging equipment.
  • 5.1 Dismantle lifting/moving equipment and packing, return to resting position and inspect for wear.
  • 5.2 Complete logbook and site records in accordance with workplace requirements.
6 Clean up.
  • 6.1 Clear work area and dispose of, reuse or recycle materials in accordance with regulatory and workplace requirements.
  • 6.2 Clean, check, maintain and store tools and equipment in accordance with manufacturer and workplace requirements.
No information
No information
Replaces
State Code National Code Title Type
D7400 CPCCRI3013A Perform intermediate rigging Unit of competency
State Code National Code Title Type
BGB5 CPC30720 Certificate III in Rigging Qualification