Unit of competency Outline

Date retreived
22/07/2026 1:48 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Prepare competition vehicle suspension

Prepare competition vehicle suspension

Unit of competency
National Code
AURMTD002
State Code
AXB93
TGA Status
Current
DTWD Status
Approved
Current Release Number
1.00
Current Release Date
14/04/2016
View on TGA
State Implementation and Classification
Approved Date
13/07/2016
Field of Education
030503 - Vehicle Mechanics
Original Release Date
13/07/2016
Nominal Hours
32
Description
This unit describes the performance outcomes required to test, dismantle, inspect, reassemble and adjust the suspension of a motor sport competition vehicle. It involves preparing for the task, selecting the correct preparation procedure, carrying out the task, performing post-preparation testing, and completing workplace processes and documentation. It requires the technical ability to determine competition vehicle suspension requirements and the effects of making changes to variables.It applies to those working in the motor sport industry. No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
Notes
Elements and Performance Criteria
1. Determine competition vehicle suspension requirements
  • 1.1 Job requirements are determined from workplace instructions and category regulations
  • 1.2 Rules and regulations and vehicle specifications and tolerances are analysed for competitive advantage
  • 1.3 Suspension requirements are determined according to vehicle operating criteria
  • 1.4 Component requirements are documented and communicated to appropriate personnel
2. Prepare for work on suspension
  • 2.1 Tools, equipment and materials are selected and checked for serviceability
  • 2.2 Work area is cleaned and laid out for job requirements according to team requirements
  • 2.3 Hazards associated with the work are identified and risks are managed according to safety requirements
  • 2.4 Vehicle is cleaned and prepared for initial measurement according to team requirements
  • 2.5 Existing suspension settings are measured and documented prior to component removal or adjustment according to workplace procedures
  • 2.6 Problems with work area or operation of the equipment are reported to appropriate personnel as required
3. Dismantle, modify and assemble non-sealed dampers
  • 3.1 Damper removal, testing and dismantling procedures are sourced and interpreted
  • 3.2 Dampers are tested, dismantled, cleaned, inspected and measured for wear, and tolerances are determined according to manufacturer specifications and safety and environmental requirements
  • 3.3 Dampers are replaced, repaired or modified as required according to manufacturer specifications, safety requirements and team procedures
  • 3.4 Dampers are prepared and tested according to manufacturer specifications and procedures, and safety requirements
4. Dismantle, replace or change springs
  • 4.1 Methods for removing and dismantling springs according to manufacturer specifications are sourced and interpreted
  • 4.2 Spring dimensions are measured and documented before dismantling
  • 4.3 Springs are disassembled and cleaned, and rates and tolerances are checked according to manufacturer specifications, workplace procedures and safety requirements
  • 4.4 Retention, replacement, adjustment or service of components is made according to team procedures
  • 4.5 Replacement springs are checked as required for rate and wear according to manufacturer specifications, workplace procedures and safety requirements
5. Configure suspension components and settings
  • 5.1 Removed suspension components are inspected for quality and readiness for installation
  • 5.2 Sub-assemblies and fasteners are installed and tensioned in correct sequence according to manufacturer specifications, workplace procedures and safety requirements
  • 5.3 Associated components, sub-assemblies and structural elements of vehicle affecting suspension configuration are checked for serviceability as required and according to manufacturer specifications, workplace procedures and safety requirements
  • 5.4 Suspension components and settings are adjusted and configured within tolerances according to manufacturer specifications, workplace procedures and safety requirements
  • 5.5 Suspension settings are documented and problems with vehicle sub-assemblies are reported to appropriate personnel according to workplace procedures
6. Complete work processes
  • 6.1 Tools and equipment are checked and stored according to team procedures
  • 6.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected
  • 6.3 Surplus material and components are checked and stored according to workplace requirements and problems are reported to appropriate personnel as required
  • 6.4 Workplace documentation is processed according to team requirements
No information
No information
Replaces
State Code National Code Title Type
WF285 AURMTD4002 Prepare competition vehicle suspension Unit of competency