Unit of competency Outline

Date retreived
22/07/2026 6:26 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Produce rotational moulded products

Produce rotational moulded products

Unit of competency
National Code
PMBPROD321
State Code
BAI63
TGA Status
Replaced
DTWD Status
Transition (Replaced)
Current Release Number
1.00
Current Release Date
22/06/2016
View on TGA
State Implementation and Classification
Approved Date
05/08/2016
Field of Education
030305 - Materials Engineering
Original Release Date
05/08/2016
Nominal Hours
52
Description
This unit of competency covers the skills and knowledge required to operate and adjust rotational moulding processes to produce product.This unit of competency applies to experienced operators who are required to start up and shut down injection moulding equipment, monitor equipment operation, establish a stable process, make adjustments to remedy faults and non-conformity and solve problems within area of responsibility.This unit of competency applies to an experienced operator demonstrating theoretical and technical knowledge and well developed skills in situations that require some discretion and judgement. The advanced operator may work alone or as a member of a team or group and will work in liaison with other shift team members, team leader and supervisor, as appropriate.No licensing, legislative or certification requirements apply to this unit at the time of publication.
Notes
Elements and Performance Criteria
1 Plan own work requirements
  • 1.1 Identify equipment and processes used for production process and upstream and downstream operations from production plan or request
  • 1.2 Identify materials required, including additives
  • 1.3 Recognise hazards and follow appropriate hazard control/minimisation methods
  • 1.4 Identify and check emergency stops, safety gates, guards and controls
  • 1.5 Identify requirements for materials, quality, production and equipment checks
  • 1.6 Identify materials, waste management and housekeeping needs
2 Start up rotational moulding process
  • 2.1 Determine equipment requirements
  • 2.2 Set process to specifications as required
  • 2.3 Check rotational moulding equipment settings and adjustments are as required
  • 2.4 Check materials are correct
  • 2.5 Discard, or make adjustments to the process for, non-conforming materials
  • 2.6 Set up date, batch and materials markings to specifications, as required
  • 2.7 Complete other pre-start checks in accordance with procedures
  • 2.8 Start up rotational moulding process
3 Operate and make adjustments as required to the rotational moulding process
  • 3.1 Operate rotational moulding equipment, noting key variables
  • 3.2 Monitor controls/displays/terminals for production/process data
  • 3.3 Monitor product/process quality in accordance with procedures
  • 3.4 Make adjustments to remedy faults and non-conformity to standard as required
  • 3.5 Maintain continuity of process
  • 3.6 Collect and reprocess/discard scrap/trim and other materials in accordance with procedures
  • 3.7 Clean, adjust and lubricate equipment as required
  • 3.8 Pause equipment, or stop equipment in an emergency, following workplace and emergency procedures
4 Anticipate and solve problems
  • 4.1 Recognise a problem or a potential problem
  • 4.2 Determine problems needing priority action
  • 4.3 Refer problems outside area of responsibility to appropriate person, with possible causes
  • 4.4 Seek information and assistance as required to solve problems
  • 4.5 Solve problems within area of responsibility
  • 4.6 Follow through items initiated until final resolution has occurred
No information
No information
Replaces
State Code National Code Title Type
W7634 PMBPROD321B Produce rotational moulded products Unit of competency
Replaced By
State Code National Code Title Type
ODB00 PMBPROD321E Produce rotational moulded products Unit of competency
State Code National Code Title Type
BCT3 PMB30116 Certificate III in Polymer Processing Qualification
BCU0 PMB40116 Certificate IV in Polymer Technology Qualification