Unit of competency Outline

Date retreived
22/07/2026 8:24 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Produce rotational moulded products

Produce rotational moulded products

Unit of competency
National Code
PMBPROD321E
State Code
ODB00
TGA Status
Current
DTWD Status
Approved
Current Release Number
1.00
Current Release Date
18/02/2021
View on TGA
State Implementation and Classification
Approved Date
19/05/2021
Field of Education
030305 - Materials Engineering
Original Release Date
19/05/2021
Nominal Hours
52
Description
This unit describes the skills and knowledge required to operate, control and optimise rotational moulding processes to produce product.This unit applies to an experienced technician working alone or as part of a team.The unit principally refers to the practical skills to operate rotational moulding equipment, as well as controlling rotational moulding production to meet the required product quality and output rate.No licensing or certification requirements exist at the time of publication. Relevant legislation, industry standards and codes of practice within Australia must be applied.
Notes
Elements and Performance Criteria
1. Plan work requirements
  • 1.1 Identify materials required, including additives, from job specifications
  • 1.2 Identify processes required for production and upstream and downstream operations from job specifications
  • 1.3 Perform pre-operational checks including checking for and controlling hazards
  • 1.4 Identify and check emergency stops, safety gates, guards and controls
  • 1.5 Identify checks and testing processes required for equipment, materials, quality and production management to meet job specifications
  • 1.6 Identify housekeeping and waste management strategies to collect excess, discarded or nonconforming materials to be disposed of, recycled or reprocessed according to workplace procedures
2. Start up rotational moulding process
  • 2.1 Verify equipment requirements against job requirements
  • 2.2 Set production process according to equipment and work specifications, and adjust process to optimise output based on selected materials
  • 2.3 Set up and adjust rotational moulding equipment settings to meet job specifications
  • 2.4 Verify materials are correct against job specifications
  • 2.5 Set up date, batch and materials markings according to workplace procedures
  • 2.6 Undertake other pre-startup checks according to equipment specifications and workplace procedures
3. Operate and make adjustments to rotational moulding equipment
  • 3.1 Start up and operate rotational moulding equipment, and make adjustments to settings to meet job specifications
  • 3.2 Ensure process is operating according to equipment specifications and workplace procedures
  • 3.3 Follow checking and testing processes to assess if output meets job specifications and quality standards, and apply strategies for managing nonconforming outputs
  • 3.4 Maintain continuity of process to support production
  • 3.5 Work efficiently to minimise scrap and trim according to workplace procedures
  • 3.6 Clean work area, and clean, adjust and lubricate equipment, according to equipment instructions and workplace procedures
  • 3.7 Pause or stop machine cycle in normal and abnormal circumstances according to workplace procedures
4. Shut down equipment
  • 4.1 Shut down equipment according to equipment instructions and workplace procedures
  • 4.2 Complete equipment clean-up and post-production adjustments according to equipment instructions and workplace procedures
  • 4.3 Put guards, locks and notices in place to prevent inadvertent startup
5. Anticipate and solve process and quality control variances
  • 5.1 Recognise existing or potential process control variances and their causes
  • 5.2 Determine, prioritise and implement remedial and preventative actions based on identified issues and causes
  • 5.3 Monitor process and quality control variances and corrective actions taken until resolved
  • 5.4 Accurately maintain records and logbooks
No information
No information
Replaces
State Code National Code Title Type
BAI63 PMBPROD321 Produce rotational moulded products Unit of competency
State Code National Code Title Type
BGP1 PMB30121 Certificate III in Polymer Processing Qualification
BGO8 PMB40121 Certificate IV in Polymer Technology Qualification