Unit of competency Outline

Date retreived
22/07/2026 3:13 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Inspect canvas or sail product

Inspect canvas or sail product

Unit of competency
National Code
LMTTF2019A
State Code
W7477
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
16/07/2011
View on TGA
State Implementation and Classification
Approved Date
24/10/2014
Field of Education
080317 - Quality Management
Original Release Date
24/10/2014
Nominal Hours
40
Description
This unit covers the skills and knowledge required to inspect canvas or sail products prior to dispatch to customers.
Notes
Elements and Performance Criteria
1 Obtain specifications and prepare inspection area
  • 1.1 Relevant workplace and customer specifications for the product are obtained
  • 1.2 Applicable workplace and industry quality standards are ascertained
  • 1.3 Work area to be used for inspection is cleared and cleaned in preparation for the inspection process
  • 1.4 Workplace procedures and instructions are read and interpreted
2 Obtain and prepare tools and equipment
  • 2.1 Measuring and marking equipment, and tools used in the inspection process are obtained and prepared for use
  • 2.2 Toolsand equipment are examined for damage, missing components or other defects (including frayed power cords where applicable)
  • 2.3 Extension power cables are checked for knots and insulation damage
  • 2.4 Electricaltools are connected safely to power supply
  • 2.5 Safety equipment is used during tool operation in accordance with OHS practices
  • 2.6 Inspection tasks are performed using tools and equipment in accordance with OHS practices
  • 2.7 Tools and equipment are cleaned after use and stored in accordance with industry and workplace OHS practices
3 Locate, transport and lay out product
  • 3.1 Completed product is located and safely transferred to the inspection area
  • 3.2 Product is laid out or hung for inspection
  • 3.3 Assistance to handle product is obtained if necessary
4 Inspect product
  • 4.1 Product is inspected to verify that it meets job specifications and relevant workplace and industry quality standards
  • 4.2 Any areas in need of rework or rectification are identified and marked
  • 4.3 Inspected product is labelled or tagged
  • 4.4 Product is folded or otherwise prepared for storage or transport
  • 4.5 Documentation is completed in accordance with workplace procedures
  • 4.6 If rework or rectification is needed, product is set aside for appropriate action to be decided
  • 4.7 Supervisor is informed of any abnormalities indicating a need for maintenance or other action elsewhere in the workplace
  • 4.8 Knowledge of inspecting processes are applied to perform required tasks
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the Performance Criteria, is detailed below. Add any essential operating conditions that may be present with training and assessment depending on the work situation, needs if the candidate, accessibility of the item, and local industry and regional contexts.
Legislative/regulatory requirements
All work must comply with relevant Federal and State or Territory legislative or regulatory requirements.
Tools and equipments may include
measuring tapes
protractors
callipers
lifting and hoisting equipment
pliers
knives
marking pens
crayons
Electrical tools may include
lifting and hoisting equipment
inspection lamps
electric staple guns
Product may include
non-complex and two dimensional products
OHS practices
OHS practices must include hazard identification and control, risk assessment and implementation of risk reduction measures specific to the tasks described by this unit, and may include:
manual handling techniques
standard operating procedures
personal protective equipment
safe materials handling
taking of rest breaks
ergonomic arrangement of workplaces
following marked walkways
safe storage of equipment
housekeeping
reporting accidents and incidents
other OHS practices relevant to the job and enterprise
The Evidence Guide provides advice on assessment and must be read in conjunction with the Performance Criteria, Required Skills and Knowledge, the Range Statement and the Assessment Guidelines for the Training Package.

Critical aspects for assessment and evidence required to demonstrate competency in this unit
Demonstrates skills and knowledge to:
perform inspection procedures on non complex products and identify faults or substandard work
interpret work instructions and inspection procedures
interpret workplace and customer specifications and relevant quality standards
comply with all relevant safety requirements including safe use of hand and power tools and electrical equipment
document inspection results and report faults or abnormalities in accordance with workplace procedures
perform normal operator maintenance of work area and inspection equipment to enable inspections to be conducted safely and efficiently
Consistently applies skills and knowledge when:
organising work
completing tasks
identifying improvements
using workplace practices
using OHS practices
recording and reporting accidents and incidents
assessing operational readiness of equipment used and work processes
recognising and adapting to cultural differences in the workplace, including modes of behaviour and interactions
completing work systematically with attention to detail without damage to goods and equipment

Context and specific resources for assessment
Assessment may occur on the job or in an appropriately simulated environment and requires access to work areas, materials and equipment, and to information on workplace practices and OHS practices.

Guidance information for assessment
This unit may be assessed independently or in combination with other relevant units.
Replaces
State Code National Code Title Type
E0979 LMTPRTF15AA Inspect product - 1 Unit of competency
E1910 LMTPRTF15BA Inspect product - 2 Unit of competency
Replaced By
State Code National Code Title Type
BAU53 MSTTF2016 Inspect canvas or sail product Unit of competency