Unit of competency Outline
Date retreived
23/07/2026 12:00 AM AWST
23/07/2026 12:00 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Mount and proof flexographic plates for basic printing
Mount and proof flexographic plates for basic printing
Unit of competency
National Code
ICPPR211C
ICPPR211C
State Code
D3155
D3155
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
09/09/2014
Field of Education
030103 - Printing
Original Release Date
09/09/2014
Nominal Hours
30
Description
This unit describes the performance outcomes, skills and knowledge required to mount and proof flexographic plates for routine printing.
Notes
Elements and Performance Criteria
1. Confirm routine job specifications
- 1.1. Job requirements are read and interpreted from job documentation or production control system
- 1.2. Set up is carried out correctly in minimum time with minimum wastage
- 1.3. Prior inspections are completed and signed off
2. Prepare flexographic plates
- 2.1. Plate height and relief are measured
- 2.2. Plates are trimmed and prepared according to mounting system requirements
- 2.3. Mounting adhesive is selected to achieve correct PCD (Pitch Circle Diameter) of specified plate cylinders and gears
3. Prepare plate cylinders
- 3.1. Plate cylinders/seamless sleeves are selected, cleaned and prepared and correct gears are mounted
- 3.2. Sleeves and correct gears on mandrels are selected, cleaned, prepared and mounted to meet routine job specifications
- 3.3. TIR (Total Indicated Runout) is checked to be within specified tolerances on plate cylinders
- 3.4. Selected mounting adhesive is applied to plate cylinders
4. Mount and/or proof flexographic plates on mounting/proofing machine
- 4.1. Plates are prepared and mounted on cylinders using pin mount or microdot systems or sleeves according to chart number/print direction OR
- 4.2. Plate mounting sheet is prepared to meet routine job specifications AND
- 4.3. Plates are mounted to position on plate mounting sheet or camera targets AND
- 4.4. Plate mounting sheet is installed and tensioned onto plate cylinder to specified chart number/print direction
- 4.5. Plates are proofed and each plate cylinder is checked for register
- 4.6. Flexographic plates are trimmed and taped down according to printing press requirements
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Jobs may include:
surface prints.
Types of plates may include:
range of plate thicknesses used in flexography
range of mounting adhesives.
Routine may include:
routine within this context relates to the set up and production of print runs that involve routine set up and routine production. The set up of equipment and production is straightforward and does not involve a significant amount of deviation from using standard equipment settings. In this sense, routine does not refer to a job that an individual might repeat on a regular basis.
Inks/coatings may include:
range of standard inks commonly used in 1-2 colour printing.
Colour matching systems may include:
use of visual colour assessment and densitometry to match basic standard colours under controlled lighting conditions.
Machines may include:
a range of stack, in-line and central impression flexographic printing machines with various plate cylinder drives and mounting systems.
Design may include:
colours, simple graphics and text. Minor variation in registration and position.
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Jobs may include:
surface prints.
Types of plates may include:
range of plate thicknesses used in flexography
range of mounting adhesives.
Routine may include:
routine within this context relates to the set up and production of print runs that involve routine set up and routine production. The set up of equipment and production is straightforward and does not involve a significant amount of deviation from using standard equipment settings. In this sense, routine does not refer to a job that an individual might repeat on a regular basis.
Inks/coatings may include:
range of standard inks commonly used in 1-2 colour printing.
Colour matching systems may include:
use of visual colour assessment and densitometry to match basic standard colours under controlled lighting conditions.
Machines may include:
a range of stack, in-line and central impression flexographic printing machines with various plate cylinder drives and mounting systems.
Design may include:
colours, simple graphics and text. Minor variation in registration and position.
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Evidence of the ability to:
prepare and mount flexographic plates and plate cylinders. Produce print direction chart and check registration, if necessary
demonstrate an ability to find and use information relevant to the task from a variety of information sources
mount and proof flexographic plates on TWO occasions for basic jobs, according to enterprise procedures and the Performance Criteria
evidence for assessment may be gathered from assessment of the unit of competency alone or through an integrated assessment activity.
Context of and specific resources for assessment
Assessment must ensure:
assessment may take place on the job, off the job or a combination of these. Off the job assessment must be undertaken in a closely simulated workplace environment
flexographic printing machines, pin mounted or microdot mounting systems, print direction chart.
Method of assessment
A range of assessment methods should be used to assess practical skills and knowledge. The following examples are appropriate for this unit:
direct questioning combined with review of portfolios of evidence and third party workplace reports of on-the-job performance by the candidate.
Guidance information for assessment
Holistic assessment with other units relevant to the industry sector, workplace and job role is recommended, for example:
ICPPR313C Set up for basic flexographic printing
ICPPR314C Produce basic flexographic printed product.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Evidence of the ability to:
prepare and mount flexographic plates and plate cylinders. Produce print direction chart and check registration, if necessary
demonstrate an ability to find and use information relevant to the task from a variety of information sources
mount and proof flexographic plates on TWO occasions for basic jobs, according to enterprise procedures and the Performance Criteria
evidence for assessment may be gathered from assessment of the unit of competency alone or through an integrated assessment activity.
Context of and specific resources for assessment
Assessment must ensure:
assessment may take place on the job, off the job or a combination of these. Off the job assessment must be undertaken in a closely simulated workplace environment
flexographic printing machines, pin mounted or microdot mounting systems, print direction chart.
Method of assessment
A range of assessment methods should be used to assess practical skills and knowledge. The following examples are appropriate for this unit:
direct questioning combined with review of portfolios of evidence and third party workplace reports of on-the-job performance by the candidate.
Guidance information for assessment
Holistic assessment with other units relevant to the industry sector, workplace and job role is recommended, for example:
ICPPR313C Set up for basic flexographic printing
ICPPR314C Produce basic flexographic printed product.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| D0417 | ICPPR211B | Mount and proof flexographic plates for basic printing | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| AUP02 | ICPPRN211 | Mount and proof flexographic plates for basic printing | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W768 | ICP20810 | Certificate II in Printing and Graphic Arts (Cartons) | Qualification |
| W761 | ICP20110 | Certificate II in Printing and Graphic Arts (General) | Qualification |
| J184 | ICP30512 | Certificate III in Printing and Graphic Arts (Printing) | Qualification |