Unit of competency Outline

Date retreived
23/07/2026 9:37 AM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Install products on and off site

Install products on and off site

Unit of competency
National Code
LMTTF2016A
State Code
W7474
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
16/07/2011
View on TGA
State Implementation and Classification
Approved Date
24/10/2014
Field of Education
030717 - Plant And Machine Operations
Original Release Date
24/10/2014
Nominal Hours
40
Description
This unit covers the skills and knowledge required to install canvas and sail products both on site and off site.
Notes
Elements and Performance Criteria
1 Prepare site
  • 1.1 Workplace procedures and instructions are read and interpreted, including interpretation of drawings and technical information to guide installation
  • 1.2 Sequence of task operations is planned
  • 1.3 Suitable electrical power outlets are identified
  • 1.4 Ladders, steps or bosun's chair are set up as required
  • 1.5 Additional assistance, if required, is arranged
  • 1.6 Site for service provision is prepared
2 Select, use and store tools
  • 2.1 Appropriate tools are selected for the job
  • 2.2 Tools are inspected for damage, missing components or other defects (including frayed power cords where applicable) prior to use
  • 2.3 Safe working environment for tool use is established
  • 2.4 Extension power cables are checked for knots and insulation damage and are safely supported when working overhead
  • 2.5 Electrical tools are safely connected to power supply
  • 2.6 Safety equipment is used in accordance with OHS practices
  • 2.7 Tools are used in accordance with OHS practices
  • 2.8 Tools are located in a safe position when not in use
  • 2.9 Tools and extension cords are cleaned and stored in accordance with industry and workplace OHS practices
3 Use ladder, steps, bosun's chair or other device
  • 3.1 Ladders or other devices such as steps or bosun's chair are appropriately selected for the tasks
  • 3.2 Ladder or other device is secured and adequately supported
  • 3.3 Appropriate barriers and signs are erected when working overhead
  • 3.4 Assistance is used as necessary when working above the ground or deck
4 Fit products
  • 4.1 Appropriate marking tools and measuring equipment are used to mark out fitting positions
  • 4.2 Products to be installed are checked to ensure they meet specifications and are fit for their intended purpose
  • 4.3 Appropriate ladders or other devices are used to gain height advantage
  • 4.4 Appropriate tools are used to drill and prepare locating holes
  • 4.5 Products are safely lifted or lowered into position
  • 4.6 Appropriate fastenings are used to attach or anchor product
  • 4.7 Pulleys or sheave blocks are fitted
  • 4.8 Ropes or cables are threaded or attached as necessary and stays or other fastenings are fitted
  • 4.9 Work area is cleaned up after fitting
  • 4.10 Appropriate OHS precautions are applied during all phases of the task
  • 4.11 Knowledge of fitting products are applied to perform required tasks
  • 4.12 Work is conducted in cooperation with other team members as required
5 Inspect and check quality
  • 5.1 Completed work is inspected to verify that the products and installation work meet job specifications and relevant workplace and industry quality standards
  • 5.2 Products are checked for correct fit, correct installation and correct operation after installation
  • 5.3 Rework or rectification requirements are determined
  • 5.4 Rework or rectification is performed or other appropriate action is taken
6 Demonstrate and provide customer information
  • 6.1 Product use and operating information is supplied to customer
  • 6.2 Product is demonstrated to customer
  • 6.3 Customer questions are answered
7 Clean up
  • 7.1 Work area is cleaned up
  • 7.2 Tools, ladders, bosun's chair or other equipment is cleaned and stowed away
  • 7.3 Project documentation is completed
  • 7.4 Customer signature is obtained, if required
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the Performance Criteria, is detailed below. Add any essential operating conditions that may be present with training and assessment depending on the work situation, needs if the candidate, accessibility of the item, and local industry and regional contexts.
Legislative/regulatory requirements
All work must comply with relevant Federal and State or Territory legislative or regulatory requirements.
Products may include
blinds
awnings
annexes
sails
Tools may include
hand tools such as:
hammers
punches
hand drills
saws
hacksaws
rasps
wire brushes
pop-rivets
expanding bolts
power tools such as:
portable electric drills
routers
portable sanders
abrasive disk cutting equipment
electric punches
OHS practices
OHS practices must include hazard identification and control, risk assessment and implementation of risk reduction measures specific to the tasks described by this unit, and may include:
manual handling techniques
standard operating procedures
personal protective equipment
safe materials handling
taking of rest breaks
ergonomic arrangement of workplaces
following marked walkways
safe storage of equipment
housekeeping
reporting accidents and incidents
other OHS practices relevant to the job and enterprise
The Evidence Guide provides advice on assessment and must be read in conjunction with the Performance Criteria, Required Skills and Knowledge, the Range Statement and the Assessment Guidelines for the Training Package.

Critical aspects for assessment and evidence required to demonstrate competency in this unit
Demonstrates skills and knowledge to:
comply with all relevant safety requirements including safe use of ladders, bosun's chair, load hoisting equipment and electrical equipment
interpret work orders, drawings and installation instruction
interpret product, and equipment specifications needed for installation and operation
perform normal installation and setting of products and equipment
inspect and test operation of installed products and equipment
specify any rectification necessary
perform normal operator maintenance of work area to enable work to be conducted safely and efficiently
document and communicate work related information including reporting of faults and other problems which do not fall within the operator's province
Consistently applies skills and knowledge when:
organising work
completing tasks
identifying improvements
using workplace practices
using OHS practices
recording and reporting accidents and incidents
assessing operational readiness of equipment used and work processes
recognising and adapting to cultural differences in the workplace, including modes of behaviour and interactions
completing work systematically with attention to detail without damage to goods and equipment

Context and specific resources for assessment
Assessment may occur on the job or in an appropriately simulated environment and requires access to work areas, materials and equipment, and to information on workplace practices and OHS practices.

Guidance information for assessment
This unit may be assessed independently or in combination with other relevant units.
Replaces
State Code National Code Title Type
E0974 LMTPRTF10AA Install products on and off site - 1 Unit of competency
E1908 LMTPRTF10BA Install products on and off site - 2 Unit of competency
Replaced By
State Code National Code Title Type
BAU54 MSTTF2015 Install products on and off site Unit of competency