Unit of competency Outline
Date retreived
22/07/2026 3:25 PM AWST
22/07/2026 3:25 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Operate a boom type elevating work platform
Operate a boom type elevating work platform
Unit of competency
National Code
TLID3035
TLID3035
State Code
AWM56
AWM56
TGA Status
Current
Current
DTWD Status
Approved
Approved
State Implementation and Classification
Approved Date
04/08/2016
Field of Education
030717 - Plant And Machine Operations
Original Release Date
04/08/2016
Nominal Hours
30
Description
This unit involves the skills and knowledge required to operate a boom type elevating work platform less than 11 metres boom length, in accordance with relevant state/territory licence/permit requirements and regulations, in a variety of operational contexts. It includes inspecting and testing elevating work platform, assessing job and work requirements, planning work and setting up for lift, and carrying out elevation. It also includes implementing planned hazard controls and strategies, and packing up work platform after operations.Work is performed with limited supervision, and with duty of care responsibility for self and others in achieving the prescribed outcomes. No licensing, legislative or certification requirements apply to this unit at the time of publication.
Notes
Elements and Performance Criteria
1 Inspect and test elevating work platform
- 1.1 Work platform is visually inspected prior to operation for evidence of damage, structural weakness or interference in accordance with pre-operational safety check procedures
- 1.2 Routine pre-operational equipment checks are carried out in accordance with available checklists
- 1.3 Work platform logbook is checked, service requirements are noted and maintenance personnel are advised of requirements
- 1.4 Elevating work platform is started in accordance with manufacturer guidelines and start-up procedures for operations, and abnormal noise or movement is reported to authorised person for corrective action
- 1.5 Start-up checks are conducted in accordance with manufacturer specifications and company procedures to ensure work platform and equipment are operating correctly
- 1.6 Faults are corrected or reported to authorised person for corrective action in accordance with company procedures
- 1.7 Operating and emergency controls are checked for correct operation in accordance with manufacturer specifications, including use of emergency decent device
- 1.8 Boom is lowered under simulated emergency conditions to check for operational effectiveness
- 1.9 Gear and accessories are checked and damaged or worn gear is segregated and reported to authorised person for testing/repair/destruction
- 1.10 Results of inspections are recorded and reported in accordance with company procedures
2 Assess job requirements and work
- 2.1 Briefing, handover details, authorisations and clearances are received, interpreted and clarified in accordance with company and site procedures, and legislative requirements
- 2.2 Work area is inspected, potential hazards are identified and appropriate elimination or control measures are selected
- 2.3 Weight of load including personnel and equipment, is correctly estimated to ensure job is within limits of work platform capacity
3 Plan work and set up for lift
- 3.1 Work plan is developed and agreed with relevant workplace personnel, including hazard prevention/control measures, and safety and emergency procedures in line with applicable Australian Standards
- 3.2 Suitable firm and level standing is chosen and prepared for location of elevating work platform
- 3.3 Outriggers and stabilisers are correctly deployed and positioned in accordance with manufacturer instructions and appropriate Australian Standards
- 3.4 Appropriate plates or packing are correctly used under footplates as required to adequately distribute loading
- 3.5 Ground is checked before and after packing is installed to ensure it is firm enough to bear load
- 3.6 Job plan is developed including hazard prevention/control measures and safety procedures in accordance with applicable Australian Standards and equipment manufacturer specifications
- 3.7 Work platform load chart is located and information on permissible loads, radii and heights is taken into account in planning job
- 3.8 Job requirements, and workplace rules and procedures are taken into account in job plan
- 3.9 Job plan is discussed and confirmed with relevant personnel
- 3.10 Work gear and tools are properly stowed in elevating work platform in accordance with Australian Standards, company procedures and guides
4 Carry out elevation
- 4.1 Configuration and operation of elevating work platform are checked as required to ensure safe lift
- 4.2 Operation of work platform is carried out in accordance with job plan, appropriate Australian Standard and manufacturer specifications
5 Implement planned hazard control strategies
- 5.1 Load is constantly monitored to ensure safety of personnel, load and structural stability
- 5.2 Unplanned situations are responded to in accordance with company procedures, in a manner that minimises risk to personnel and equipment
- 5.3 Required signals are correctly given, interpreted and followed in accordance with appropriate Australian Standards
6 Pack up work platform
- 6.1 Elevating work platform is shut down using correct sequence of procedures in accordance with manufacturer instructions
- 6.2 Routine post-operational equipment checks are carried out in accordance with manufacturer instructions and available checklists, and defects are recorded and reported in accordance with company procedures
- 6.3 Elevating work platform is dismantled in accordance with job plan, manufacturer instructions and relevant statutory regulations
- 6.4 Outriggers and stabilisers are secured and stowed in accordance with manufacturer instructions
- 6.5 Elevating work platform is correctly stowed and secured in accordance with manufacturer instructions and company procedures
No information
No information
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| D5085 | TLID3035A | Operate a boom type elevating work platform | Unit of competency |